Equipment and Calibration History
Page: 1 2 [3] 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65| Ser No. | Date | Loc From | Title | Loc To | Notes |
|---|---|---|---|---|---|
| LI-7700 TG1-0211 | 2024-01-11 | Mayberry | Calibration | Mayberry | Calibration Location: Mayberry Last calibration: 2023-07-20 RSSI=71%, Optical RH=3% Ambient P=102.1kPa, Tair=11.5C Zero Air at 1850psi, AMP CA03923 3.3865 at 1700 CH4 Zero Offset: .032ppm CH4 Span Offset: .0095ppm Notes: Breezy day |
| LI-7500A 75H-2182 | 2024-01-10 | Lab | Calibration | Lab | Last calibration: 2023-10-23 AGC=103 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.21kPa, Tair=21.2C, Tdew=9.47C Zero Air at 450psi, AMP CA04119 524.77 at 650 Tdewspan=18.00 CO2 zero 0.8848 -> .885 Offset: .94ppm CO2 span 1.0124 -> 1.0163 Offset: -2.06ppm H2O zero 0.8311 -> .8326 Offset: 9.9ppm H2O span 1.0325 -> 1.0352 Offset: -.05ppm Notes: Vertical orientation. Reset SS from 103 to 100 after cal. Used nail polish to cover up some small patches of paint missing from the spars. |
| LI-7500A 1594 | 2024-01-10 | Lab | Calibration | Lab | Last calibration: 2023-10-03 AGC=103 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.22kPa, Tair=21.03C, Tdew=9.42C Zero Air at 450psi, AMP CA04119 524.77 at 675 Tdewspan=18.00 CO2 zero 0.8777 -> .8774 Offset: -1.37ppm CO2 span 1.0092 -> 1.0093 Offset: -.7ppm H2O zero 0.8117 -> .8142 Offset: 14.7ppm H2O span 1.0074 -> 1.0062 Offset: .03ppm Notes: Vertical orientation. Reset SS from 103 to 100 after cal. |
| LI-7700 TG1-0155 | 2024-01-10 | Lab | Calibration | Lab | Calibration Location: Lab Last calibration: 2023-06-15 RSSI=91%, Optical RH=21% Ambient P=100.46kPa, Tair=21.3C Zero Air at 500psi, AMP CA04119 4.2238 at 750 CH4 Zero Offset: -.03ppm CH4 Span Offset: -.0188ppm Notes: This sensor was removed from WP with its decommissioning. Back in the lab, it had revert to default heater settings and its clock was off (laptop=11:46, 7700=18:51, "Etc/GMT+8" on slave). I changed the clock setting to automatic, set the clock to match the laptop time, changed the clock setting back to slave, and then rebooted. The time was correct after reboot but we should double-check it after conencting to the 7550 in the field. I changed the heater settings back to our usual. Before calibration, I flushed the optics headspace down to 10% and swapped in a bottle of fresh drierite. |
| LI-7500A 0041 | 2024-01-04 | Lab none | Installed | Mayberry Gas Analyzer CO2/H2O | Installed at Mayberry to replace sn 0073 for calibration. |
| LI-7500A 0073 | 2024-01-04 | Mayberry Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Mayberry for calibration. Replaced by sn 0041. |
| LI-7500A 1594 | 2024-01-04 | West Pond Gas Analyzer CO2/H2O | Removed | Lab none | Removed from WP tower with initial decommissioning of the site |
| LI-7700 TG1-0155 | 2024-01-04 | West Pond Gas Analyzer CH4 | Removed | Lab none | Removed from WP tower with initial decommissioning of the site |
| LI-7500A 75H-2180 | 2024-01-04 | Lab none | Installed | East End Gas Analyzer CO2/H2O | Installed at East End to replace sn 75H-2182 for calibration. |
| LI-7500A 75H-2182 | 2024-01-04 | East End Gas Analyzer CO2/H2O | Removed | Lab none | Removed from East End for calibration. Replaced by sn 75H-2180. |
| SI-131 1076 | 2024-01-04 | Bouldin Corn Infrared Temperature South | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| SI-131 1073 | 2024-01-04 | Bouldin Corn Infrared Temperature North | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| CH150 2963 | 2024-01-04 | Bouldin Corn Solar Controller Surface Renewal | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| CR1000X 1132 | 2024-01-04 | Bouldin Corn Data Logger Surface Renewal | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| LI-7500A 0065 | 2024-01-04 | Lab none | Installed | Bouldin Corn Gas Analyzer CO2/H2O | Installed at Bouldin Corn to replace sn 0042 for calibration. |
| LI-7500A 0042 | 2024-01-04 | Bouldin Corn Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Corn for calibration. Replaced by sn 0065. |
| SI-121 1635 | 2024-01-04 | Bouldin Alfalfa Infrared Temperature South | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| SI-131 1071 | 2024-01-04 | Bouldin Alfalfa Infrared Temperature North | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| CH150 1688 | 2024-01-04 | Bouldin Alfalfa Solar Controller Surface Renewal | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| CR1000X 1130 | 2024-01-04 | Bouldin Alfalfa Data Logger Surface Renewal | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| LI-7500A 0035 | 2024-01-02 | Lab none | Installed | Vaira Gas Analyzer CO2/H2O | Installed at Vaira to replace sn 0065 for calibration |
| LI-7500A 0065 | 2024-01-02 | Vaira Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Vaira for calibration. Replaced by sn 0035. |
| PRB-K Type #8 00000A3D04E8 | 2024-01-02 | Tonzi none | Removed | Lab none | This probes has been broken for a long time - more than a year. Removed. It has a broken pin and the shaft is cracked. |
| LI-7500A 75H-2669 | 2024-01-02 | Lab none | Installed | Tonzi-Tower Gas Analyzer CO2/H2O | Installed at Tonzi Tower to replace sn 75H-2180 for calibration. |
| LI-7500A 75H-2180 | 2024-01-02 | Tonzi-Tower Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Tonzi-Tower for calibration. Replaced by sn 75H-2669. |
| LI-7500A 75H-2667 | 2024-01-02 | Lab none | Installed | Tonzi Gas Analyzer CO2/H2O Floor | Installed at Tonzi Floor to replace sn 0041 for calibration. |
| LI-7500A 0041 | 2024-01-02 | Tonzi Gas Analyzer CO2/H2O Floor | Removed | Lab none | Removed from Tonzi Floor for calibration. Replaced by sn 75H-2667. |
| LI-7500A 0065 | 2024-01-03 | Lab | Calibration | Lab | Last calibration: 2023-09-18 AGC=100 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=22.7C, Tdew=7.3C Zero Air at 550psi, AMP CA04119 524.77 at 700 Tdewspan=20.0 CO2 zero 0.8919 -> 0.8918 Offset: -0.27ppm CO2 span 1.024 -> 1.0255 Offset: -1.3ppm H2O zero 0.7322 -> 0.7329 Offset: 4.9ppm H2O span 1.0226 -> 1.0238 Offset: -0.02ppm Notes: Signal strength rest from 107 to 100 before calibration. Used CO2 span pt of 524.67 |
| LI-7500A 0041 | 2024-01-03 | Lab | Calibration | Lab | Last calibration: 2023-09-18 AGC=100 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=22.7C, Tdew=7.3C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=20.0 CO2 zero 0.9965 -> 0.9963 Offset: -0.79ppm CO2 span 1.0192 -> 1.0217 Offset: -1.67ppm H2O zero 0.8236 -> 0.8245 Offset: 5.0ppm H2O span 1.0292 -> 1.0365 Offset: -0.16ppm Notes: H20 took a long time (40min) to stabilize - kept creeping up |
| LI-7500A 75H-2180 | 2024-01-03 | Lab | Calibration | Lab | Last calibration: 2023-09-18 AGC=101.1 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=23.1C, Tdew=7.9C Zero Air at 500psi, AMP CA04119 524.77 at 700 Tdewspan=20.0 CO2 zero 0.9143 -> 0.9141 Offset: -0.8ppm CO2 span 1.0384 -> 1.0406 Offset: -1.17ppm H2O zero 0.8944 -> 0.8965 Offset: 12.9ppm H2O span 1.0344 -> 1.0383 Offset: -0.08ppm Notes: |
| LI-7500A 0035 | 2024-01-02 | Lab | Calibration | Lab | Last calibration: 2023-08-04 AGC=100.5 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=101.0kPa, Tair=19.96C, Tdew=8.97C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9377 -> 0.9372 Offset: -2.0ppm CO2 span 1.024 -> 1.0267 Offset: -1.77ppm H2O zero 0.8984 -> 0.9006 Offset: 13.4ppm H2O span 1.0205 -> 1.0400 Offset: -0.4ppm Notes: I painted some scratches on the body with nail polish |
| HYDROS21 H21G200002433 | 2023-12-22 | Lab none | Installed | Hill Slough Water Level | Installed at the channel to replace the one that failed and was removed a while ago. |
| LI-7500A 75H-2514 | 2023-12-22 | Lab none | Installed | Bouldin Alfalfa Gas Analyzer CO2/H2O | Installed at Bouldin Alfalfa to replace sn 0035 for calibration. |
| LI-7500A 0035 | 2023-12-22 | Bouldin Alfalfa Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Alfalfa for calibration. Replaced by sn 75H-2514. |
| HMP45AC D4420028 | 2023-12-22 | Lab none | Installed | Mayberry RH & Temp | Installed at MB to replace HMP155 that died and was removed last visit. HMP155 cable removed this time. Met program updated for different AirT offset. |
| LI-7500A 75H-2669 | 2023-12-20 | Lab | Calibration | Lab | Last calibration: 2023-08-04 AGC=100.0 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=99.6kPa, Tair=22.4C, Tdew=15.48C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9195 -> 0.9187 Offset: -3.0ppm CO2 span 1.0167 -> 1.0167 Offset: -0.02ppm H2O zero 0.9009 -> 0.9027 Offset: 10.9ppm H2O span 1.0163 -> 1.0206 Offset: -0.09ppm Notes: Reset SS from 102.6 |
| LI-7500A 75H-2667 | 2023-12-20 | Lab | Calibration | Lab | Last calibration: 2023-07-10 AGC=100.0 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=99.6kPa, Tair=21.7C, Tdew=10.4C Zero Air at 500psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9411 -> 0.9413 Offset: 0.7ppm CO2 span 1.0232 -> 1.0207 Offset: 1.83ppm H2O zero 0.8427 -> 0.8427 Offset: 0.2ppm H2O span 1.0367 -> 1.0363 Offset: 0.01ppm Notes: Reset SS from 103.0, Database says last cal was 07-14, instrument says 07-10. |
| LI-7500A 75H-2514 | 2023-12-20 | Lab | Calibration | Lab | Last calibration: 2023-07-10 AGC=100.0 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=99.6kPa, Tair=20.4C, Tdew=11.0C Zero Air at 600psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9049 -> 0.9095 Offset: -3.4ppm CO2 span 1.0199 -> 1.0207 Offset: -0.37ppm H2O zero 0.8426 -> 0.8461 Offset: 3.5ppm H2O span 1.0244 -> 0.9962 Offset: -0.03ppm Notes: Calibration after factory repair and calibration. Reset SS from 103.4. Added SD coefficients to configuration. |
| eosFD FD20200001 | 2023-12-13 | Vaira Forced Diffusion North | Moved | Tonzi-SoilCO2 Forced Diffusion Tree 1 | Moved from Vaira North location to the Tonzi Tree 1 location. waiting for one FD to be repaired by Eosense. |
| PA-II-SD 68c63acc07a9 | 2023-12-07 | Lab none | Installed | Bouldin Corn Air Quality Sensor | Installed on the BC tower in its usual spot on the southwest corner. This PA has a new card slot that Joe put in. I had brought the sensor home last week so that it could reset its clock on my wifi. However, now campus has an IOT wifi network, so maybe I can try connecting the PA to it next time. |
| HYDROS21 H21G200002263 | 2023-12-08 | Lab none | Installed | Mayberry Water Level | Installed on the northeastern corner of the Mayberry scaffolding. There's not much water right now, but I tried to install it right above the muck. |
| HMP155 T2820180 | 2023-12-08 | Mayberry RH & Temp | Removed | Lab none | Removed from the Mayberry tower and brought back to the lab for testing. It was reading -79 deg C and 0% RH. |
| HMP45AC D4420028 | 2023-12-13 | Lab none | Tested | Lab none | Plugged in for a few minutes in a lab and still compares fine with the cal kit HMP155. We will use this sensor Mayberry to replace the dead HMP155 sn T2820180. |
| LI-7500A 75H-2514 | 2023-11-13 | Factory none | Calibration | Factory none | Calibrated at Licor after chopper motor replacement - see RMA doc: rma_Licor_00248550_sn75H-2514_20231201.pdf. The new calibration numbers (see cal doc: cal_Licor_LI-7500A_sn75H-2514_20231113.pdf) will need to be manually entered in 7550 configuration file. |
| LI-7500A 75H-2514 | 2023-12-05 | Factory none | Received | Lab none | Received back from Licor after chopper motor replacement and recalibration |
| LI-7810 TG10-01751 | 2023-12-01 | Lab none | Calibration | Lab none | Last calibration: 2023-08-22 Zero Air at ???psi, AMP CA04119 4223.8 ppb CH4 at ???psi CO2 zero Offset: -0.024ppm H2O zero Offset: -10.52ppm CH4 zero Offset: 0.129ppb CH4 span Offset: -1ppb Notes: Calibration in the lab before Kuno's field campaign next week. Ran zero and span gases at our usual flow rate of 2 SCFH and plumbed the system with the recommended 30cm vent before the air inlet to vent excess air pressure and to prevent diffusion of ambient air into the gas stream. I waited until the slope of H2O was <0.002ppm to set the zero. I waited until the slope of CH4 was <0.002ppb to set the span. Plan 45min+ for H2O zero to stabilize. I forgot to write down the exact CH4 span offset, but I saved a screenshot and estimated the offset based on the graph. |
| LI-7550 AIU-1866 | 2023-12-01 | Factory none | Received | Lab none | Received back from Licor. This 7550 sn AIU-1866 went back to Licor for a power problem. Licor replaced the 7550 main power supply under warranty, subjected the units to environmental tests and verified the operation of the units. It was shipped with 7500A sn 75H-2669 (nothing wrong with the 7500A, it was just the sensor attached when the box died) |
| LI-7500A 75H-2669 | 2023-12-01 | Factory none | Received | Lab none | Received back from Licor. It was shipped with LI-7550 sn AIU-1866 which went back to Licor for (another) power board repair. There was nothing wrong with this 7500A sn 75H-2669, but Israel requested we send it back as well b/c it was connected when the LI-7550 broke. Licor replaced the 7550 power supply, subjected the units to environmental tests and verified the operation of the units. |
| eosFD FD20180048 | 2023-11-13 | Tonzi-SoilCO2 Forced Diffusion Open | Removed | Lab none | Removed because CO2 readings seem to be too low. We tried a performance check but missed being able to reset the offset. Brought to the lab for testing. |
| BB-Fab BB-TF | 2023-11-13 | Tonzi Battery Bank Floor | Upgrade | Tonzi Battery Bank Floor | We removed four flooded batteries that came from the Tower. Two are probably still good. The other two seemed to be internally shorted. Four new group 27 AGM batteries were installed. |
| GP-001 GP20160117 | 2023-11-28 | Lab none | Installed | Gilbert Tract CO2 Probe | Installed at GT to replace GP20210002, which was removed b/c of noisy data. |
| GP-001 GP20210002 | 2023-11-28 | Gilbert Tract CO2 Probe | Removed | Lab none | Removed from GT because of noisy data. Replaced by GP20160117. |
| PA-II-SD 84f3ebd5ffb1 | 2023-11-20 | Bouldin Corn Air Quality Sensor | Removed | Lab none | Removed from BC tower and brought back to the lab. It needs a new data card slot. The current card slot has a bad spring mechanism so cards don't physically mount. |
| PA-II-SD 84f3ebd5ffb1 | 2022-11-02 | Lab none | Installed | Bouldin Corn Air Quality Sensor | Installed at BC on the tower |
| CR10X 3501 | 2023-11-14 | Lab none | Maintenance | Lab none | Put in a new internal lithium battery and testing in the lab. May use this datalogger for the PAR/RNET sensors on the BWW roof because I was having trouble connecting to the Goldstein lab CR10X. |
| CR10X 13214 | 2023-11-14 | Lab none | Tested | Lab none | Sticker on datalogger says it has a new internal battery as of November 2022. I was able to connect but the connection kept flickering. |
| LI-7500A 75H-2150 | 2023-11-09 | Lab | Calibration | Lab | Last calibration: 2023-08-04 AGC=97.0 SDM= DAC1= DAC2= AIU sn AIU-1039, Presure A0=58.372, A1=15.4 Ambient P=101.1kPa, Tair=22.35C, Tdew=7.4C Zero Air at 650psi, AMP CA04119 524.77 at 775 Tdewspan=20.00 CO2 zero 0.9031 -> .9041 Offset: 4.64ppm CO2 span 1.0207 -> 1.018 Offset: 1.96ppm H2O zero 0.873 -> .8731 Offset: .6ppm H2O span 1.0346 -> 1.0265 Offset: .18ppm Notes: Using loner AMP 7550 box. Removed and re-installed on BWW tower on the same day. At the BWW tower, I refilled the wash reservoir (it was empty) and checked the HMP fan (it was working, just quiet). |
| LI-7500A 75H-2669 | 2023-11-09 | Lab none | Factory none | Shipped back to Licor for repair of 7550 sn AIU-1866. This head was sent back to to the factory at Israel's request since it was the head connected to the 7550 when the 7550 died. | |
| LI-7550 AIU-1866 | 2023-11-09 | Lab none | Shipped | Factory none | Shipped back to Licor for repair. It was sent with 7500A sn 75H-2669. |
| LI-7500A 75H-2176 | 2023-11-03 | Lab | Calibration | Lab | Last calibration: 2023-07-20 AGC=101.1 SDM= DAC1= DAC2= AIU sn AIU-1039, Presure A0=58.372, A1=15.4 Ambient P=100.8kPa, Tair=25.1C, Tdew=9.77C Zero Air at 700psi, AMP CA04119 524.77 at 800 Tdewspan=20.00 CO2 zero 0.868 -> .8678 Offset: -.77ppm CO2 span 1.0095 -> 1.0116 Offset: -1.47ppm H2O zero 0.8525 -> .8552 Offset: 15.8ppm H2O span 0.9124 -> .9231 Offset: -.26ppm Notes: Using loaner AMP 7550 sn AIU-1039. Dewpoint generator had low flow; fixed one of the condenser tubing which had a crack and flow was back to normal. Vertical orientation. |
| LI-7500A 75H-2176 | 2023-11-06 | Lab none | Installed | Gilbert Tract Gas Analyzer CO2/H2O | Installed at Gilbert Tract to replace sn 75H-2669 for calibration. |
| LI-7500A 75H-2669 | 2023-11-06 | Gilbert Tract Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Gilbert Tract for calibration. Replaced by sn 75H-2176. |
| CR6 2115 | 2023-11-07 | Loaned none | Returned | Lab none | Returned from Yuankun Xu (Roland Burgmann Lab) and Yifang Cheng at the conclusion of their field project at the Slumgullion Landslide site in Colorado. |
| CR6 2114 | 2023-11-07 | Loaned none | Returned | Lab none | Returned from Yuankun Xu (Roland Burgmann Lab) and Yifang Cheng at the conclusion of their field project at the Slumgullion Landslide site in Colorado. |
| WM 1590 153804 | 2023-11-07 | Loaned none | Returned | Lab none | Returned from Yuankun Xu (Roland Burgmann Lab) and Yifang Cheng at the conclusion of their field project at the Slumgullion Landslide site in Colorado. |
| WM 1590 152603 | 2023-11-07 | Loaned none | Returned | Lab none | Returned from Yuankun Xu (Roland Burgmann Lab) and Yifang Cheng at the conclusion of their field project at the Slumgullion Landslide site in Colorado. |
| LI-610 DPG478B | 2023-11-03 | Lab none | Maintenance | Lab none | The "from condenser" tubing was cracked so air flow was really low. Joe pulled out the old tubing with a pair of pliers and replaced it with fresh tubing. Air flow is better now. |
| LI-7550 AIU-1039 | 2023-11-02 | Disposed none | Borrowed | Lab none | Borrowed from AMP for while our LI-7550 sn AIU-1866 is back at Licor for repairs. Came with AMP LI-7500A sn 75H-2418, a 7550 thermistor, IRGA cable, and IRGA mount. It is running firmware 8.8.31. |
| LI-7500A 75H-2418 | 2023-11-02 | Disposed none | Borrowed | Lab none | Borrowed from AMP for while our LI-7550 sn AIU-1866 is back at Licor for repairs. Came with AMP LI-7550 sn AIU-1039, a 7550 thermistor, IRGA cable, and IRGA mount. |
| CS451 70011236 | 2023-10-27 | Mayberry Water Level | Removed | Lab none | Removed from MB because not working |
| LI-7550 AIU-1866 | 2023-10-26 | Gilbert Tract Interface LI-7550 | Removed | Lab none | Removed because of a blown fuse. We tried replacing the fuse, but it blew immediately. |
| LI-7500A 0418 | 2023-10-26 | Lab none | Installed | Hill Slough Gas Analyzer CO2/H2O | Installed at Hill Slough to replace sn 75H-2176 for calibration. |
| LI-7500A 75H-2176 | 2023-10-26 | Hill Slough Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Hill Slough for calibration. Replaced by sn 0418. |
| LI-7500A 75H-2182 | 2023-10-27 | Lab none | Installed | East End Gas Analyzer CO2/H2O | Installed at East End to replace sn 75H-2667 for calibration. |
| LI-7500A 75H-2667 | 2023-10-27 | East End Gas Analyzer CO2/H2O | Removed | Lab none | Removed from East End for calibration. Replaced by sn 75H-2182. |
| LI-7550 AIU-1569 | 2023-10-27 | Lab none | Installed | Gilbert Tract Interface LI-7550 | Installed with wood screws to 2x4 to replace the broken box removed yesterday |
| EXO pH-ORP 22D102641 | 2023-10-18 | Lab none | Installed | Hill Slough pH-ORP | Installed in the Hill Slough channel after calibration in the lab. The whole sonde was raised about 20cm to keep it out of the mud. |
| EXO Wiped Cond/Temp 23D104030 | 2023-10-18 | Lab none | Installed | Hill Slough Conductivity Sensor | Installed in the Hill Slough channel after calibration in the lab. The whole sonde was raised about 20cm to keep it out of the mud. |
| EXO fDOM 22E100649 | 2023-10-18 | Lab none | Installed | Hill Slough fDOM | Installed in the Hill Slough channel after calibration in the lab. The whole sonde was raised about 20cm to keep it out of the mud. |
| EXO Turbidity 22E106072 | 2023-10-18 | Lab none | Installed | Hill Slough Turbidity | Installed in the Hill Slough channel after calibration in the lab. The whole sonde was raised about 20cm to keep it out of the mud. |
| EXO2 22C103416 | 2023-10-18 | Lab none | Installed | Hill Slough Water Level | Installed in the Hill Slough channel after calibration in the lab. The whole sonde was raised about 20cm to keep it out of the mud. |
| LI-7500A 75H-2182 | 2023-10-23 | Lab | Calibration | Lab | Last calibration: 2023-07-10 AGC=99.8 SDM= DAC1= DAC2= AIU sn AIU-1569, Presure A0=58.004, A1=15.479 Ambient P=100.1kPa, Tair=25.2C, Tdew=15.7C Zero Air at 700psi, AMP CA04119 524.77 at 775 Tdewspan=20.00 CO2 zero 0.8856 -> .8848 Offset: -4.04ppm CO2 span 1.0165 -> 1.0124 Offset: 2.9ppm H2O zero 0.8294 -> .8311 Offset: 10.9ppm H2O span 1.0313 -> 1.0325 Offset: -.03ppm Notes: Vertical orientation. Before calibration, cleaned dusty spars and lots of bird poop on body. |
| LI-7500A 0418 | 2023-10-23 | Lab | Calibration | Lab | Last calibration: 2023-07-19 AGC=97.3 SDM= DAC1= DAC2= AIU sn AIU-1569, Presure A0=58.004, A1=15.479 Ambient P=100.1kPa, Tair=23.1C, Tdew=29.0C Zero Air at 700psi, AMP CA04119 524.77 at 775 Tdewspan=20.00 CO2 zero 0.907 -> .9072 Offset: .71ppm CO2 span 1.0069 -> 1.0066 Offset: .14ppm H2O zero 0.933 -> .9331 Offset: .6ppm H2O span 1.0049 -> 1.0052 Offset: -.01ppm Notes: Vertical orientation. Changed SS from 97.3 to 100 before calibration. |
| LI-7500A 75H-2514 | 2023-10-10 | Lab none | Shipped | Factory none | Shipped back to Licor for repair |
| EXO pH-ORP 22D102641 | 2023-06-14 | Lab none | Installed | Hill Slough pH-ORP | Installed new tip on pH/ORP probe |
| EXO pH-ORP 22D102641 | 2023-10-11 | Hill Slough pH-ORP | Removed | Lab none | Removed for inspection in the lab because turbidy/fDOM/ph/ORP look weird |
| EXO Wiped Cond/Temp 23D104030 | 2023-10-11 | Hill Slough Conductivity Sensor | Removed | Lab none | Removed for inspection in the lab because turbidy/fDOM/ph/ORP look weird |
| EXO fDOM 22E100649 | 2023-10-11 | Hill Slough fDOM | Removed | Lab none | Removed for inspection in the lab because turbidy/fDOM/ph/ORP look weird |
| EXO Turbidity 22E106072 | 2023-10-11 | Hill Slough Turbidity | Removed | Lab none | Removed for inspection in the lab because turbidy/fDOM/ph/ORP look weird |
| EXO2 22C103416 | 2023-10-11 | Hill Slough | Removed | Lab none | Removed for inspection in the lab because turbidy/fDOM/ph/ORP look weird |
| LI-7500A 0042 | 2023-10-11 | Lab none | Installed | Bouldin Corn Gas Analyzer CO2/H2O | Installed at Bouldin Corn to replace sn 0418 for calibration. |
| LI-7500A 0418 | 2023-10-11 | Bouldin Corn Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Corn for calibration. Replaced by sn 0042. |
| LI-7500A 0073 | 2023-10-11 | Lab none | Installed | Mayberry Gas Analyzer CO2/H2O | Installed at Mayberry to replace sn 75H-2182 for calibration. |
| LI-7500A 75H-2182 | 2023-10-11 | Mayberry Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Mayberry for calibration. Replaced by sn 0073. |
| LI-7500A 0073 | 2023-10-05 | Lab | Calibration | Lab | Last calibration: 2023-06-13 AGC=100.6 SDM= DAC1= DAC2= AIU sn AIU-1569, Presure A0=58.004, A1=15.479 Ambient P=100.39kPa, Tair=30.62C, Tdew=11.88C Zero Air at 725psi, AMP CA04119 524.77 at 800 Tdewspan=20.00 CO2 zero 0.9161 -> .9167 Offset: 2.66ppm CO2 span 1.0093 -> 1.0064 Offset: 2.19ppm H2O zero 0.8328 -> .8296 Offset: -17.9ppm H2O span 1.0281 -> 1.0109 Offset: .38ppm Notes: Vertical orientation. Slightly larger than usual H2O zero offset |
| LI-7500A 0042 | 2023-10-05 | Lab | Calibration | Lab | Last calibration: 2023-06-13 AGC=99.7 SDM= DAC1= DAC2= AIU sn AIU-1569, Presure A0=58.004, A1=15.479 Ambient P=100.48kPa, Tair=27.9C, Tdew=14.5C Zero Air at 750psi, AMP CA04119 524.77 at 800 Tdewspan=20.00 CO2 zero 0.9486 -> .9473 Offset: -5.2ppm CO2 span 1.0184 -> 1.0033 Offset: 10.51ppm H2O zero 0.8461 -> .8474 Offset: 7.7ppm H2O span 1.039 -> 1.0075 Offset: -.08ppm Notes: Vertical orientation. CO2 span offset larger than usual. |
| AM16/32B 31675 | 2023-10-04 | Lab none | Installed | Tonzi Multiplexer Tower | Installed on the Tower top to replace sn 1237 which was removed due to spikes on multiple channels. |
| AM16/32A 1237 | 2023-10-04 | Tonzi Multiplexer Tower | Removed | Lab none | Removed from the Tower top due to spikes on multiple channels. Replaced by sn 31675 |
| LI-7500A 1594 | 2023-10-04 | Lab none | Installed | West Pond Gas Analyzer CO2/H2O | Installed at West Pond to replace sn 75H-2514, which needs to go back to the factory for RMA (PLL error, CO2 and H2O were both 0). |
| LI-7500A 75H-2514 | 2023-10-04 | West Pond Gas Analyzer CO2/H2O | Removed | Lab none | Removed from West Pond because of PLL error; CO2 and H2O were both 0. Not sure if this is because of sensor age or because of daily power cycles from a failing solar power system. Replaced by sn 1594. |