Equipment and Calibration History
Page: 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65| Ser No. | Date | Loc From | Title | Loc To | Notes |
|---|---|---|---|---|---|
| LI-7500A 0418 | 2021-12-01 | Mayberry Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Mayberry and brought back to the lab for testing. It was not giving any data for CO2, H2O or SS. Replaced by sn 1594. |
| miniDOT-usb 931528 | 2021-12-01 | Hill Slough DO Sensor | Removed | Lab none | Removed from HS and brought back to the lab to swap its batteries. |
| PTB110 L2340502 | 2021-12-01 | Bouldin Corn Barometer | Removed | Lab none | Removed from BC because it was giving bad data of 80 kPa and brought back to the lab for testing |
| HMP45AC U3030041 | 2021-12-01 | Bouldin Alfalfa none | Removed | Lab none | Removed from the BA HMP intercomparison from wiring position DE1/2 because it was giving bad data. It was brought back to the lab for testing. |
| TE525MM 65560-615 | 2021-12-01 | Bouldin Alfalfa Precipitation | Tested | Bouldin Alfalfa Precipitation | We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 50 tips so this bucket is good to go until next year. |
| LI-7700 TG1-0211 | 2021-12-01 | Hill Slough | Calibration | Hill Slough | Calibration Location: Hill Slough Last calibration: 2021-06-01 RSSI=72%, Optical RH=38% Ambient P=101.6kPa, Tair=16.6C Zero Air at 950psi, AMP CA04396 1.9317 at 1500 CH4 Zero Offset: -.066ppm CH4 Span Offset: .0633ppm Notes: Relatively still day. After calibration, flushed out headspace until optics RH=10% and swapped out desiccant bottle for one with fresh drierite. Zero air tank pressure uncertain--wonky regulator. |
| LI-7700 TG1-0423 | 2021-12-01 | East End | Calibration | East End | Calibration Location: East End
Last calibration: 2021-06-01 RSSI=83%, Optical RH=15% Ambient P=101.2kPa, Tair=19.2C Zero Air at 1200psi, AMP CA04396 1.9317 at 1800 CH4 Zero Offset: .007ppm CH4 Span Offset: .0023ppm Notes: Relatively still day. Did not change drierite or flush headspace with zero air. Zero air tank pressure uncertain--wonky regulator. |
| LI-7700 TG1-0421 | 2021-11-30 | West Pond | Calibration | West Pond | Calibration Location: West Pond Last calibration: 2021-06-01 RSSI=87%, Optical RH=18% Ambient P=101.4kPa, Tair=18.6C Zero Air at 100psi, AMP CA04396 1.9317 at 1750 CH4 Zero Offset: .050ppm CH4 Span Offset: .0023ppm Notes: Relatively still day. The zero air tank pressure may have been >100psi, but the regulator was wonky. Zero was stable for 2min after applying zero. |
| LI-7700 TG1-0424 | 2021-11-30 | Gilbert Tract Gas Analyzer CH4 | Calibration | Gilbert Tract Gas Analyzer CH4 | Calibration Location: Gilbert Tract
Last calibration: 2021-06-01 RSSI=85%, Optical RH=22% Ambient P=102.1kPa, Tair=15.2C Zero Air at 100psi, AMP CA04396 1.9317 at 1800 CH4 Zero Offset: .032ppm CH4 Span Offset: -.0197ppm Notes: Relatively still day with a lot of visitors to the site. The zero air tank pressure may have been >100psi, but the regulator was wonky. Zero was stable for 2min after applying zero. Swapped out the desiccant one for one with new drierite after calibration. I didn't flush out the headspace because I wanted to preserve the zero air for more calibrations that day. |
| LI-7700 TG1-0155 | 2021-12-01 | Bouldin Alfalfa | Calibration | Bouldin Alfalfa | Calibration Location: Bouldin Alfalfa
Last calibration: 2021-05-10 RSSI=84%, Optical RH=3% Ambient P=101.7kPa, Tair=21.4C Zero Air at 1050psi, AMP CA04396 1.9317 at 1700 CH4 Zero Offset: .022ppm CH4 Span Offset: -.0087ppm Notes: Relatively still day. Zero air tank pressure uncertain--wonky regulator. |
| LI-7700 TG1-0357 | 2021-12-01 | Bouldin Corn | Calibration | Bouldin Corn | Calibration Location: Bouldin Corn
Last calibration: 2021-06-24 RSSI=73%, Optical RH=24% Ambient P=101.7kPa, Tair=20.9C Zero Air at 1100psi, AMP CA04396 1.9317 at 1700 CH4 Zero Offset: 0.021ppm CH4 Span Offset: -.0017ppm Notes: Relatively still day, lots of geese in the air. After calibration, flushed headspace with zero air until optics RH=10%. Swapped out the desiccant bottle for one with fresh drierite. Zero air tank pressure uncertain--wonky regulator. |
| RPI0W RPI0W-003 | 2021-11-04 | Mayberry | Removed | Lab none | Removed from MB and brought back to the lab for repair. It wouldn't turn on, probably because of all the repeated power cycling. I think it ended up being a bad/corrupted microSD card. I set up the camera with a fresh microSD card. |
| PAR-LITE 040411 | 2021-11-18 | East End PAR Sensor Diffuse | Removed | Lab none | Removed from the wooden 4x4 on the EE tower and brought back to the lab for inspection/repair. At least one of the cable splices is partly exposed and needs to be re-spliced. |
| LI-7500A 75H-2182 | 2021-11-30 | Lab | Calibration | Lab | Last calibration: 2021-05-25 AGC=100.0 SDM=0 DAC1=- DAC2=- Ambient P=100.8kPa, Tair=27.1C, Tdew=12.5C Zero Air at 1400psi, AMP CA04119 524.77 at 1700 Tdewspan=20.0 CO2 zero 0.8846 -> 0.8850 Offset: 1.7ppm CO2 span 1.0217 -> 1.0219 Offset: -0.07ppm H2O zero 0.8464 -> 0.8470 Offset: 4.0ppm H2O span 1.024 -> 1.0264 Offset: -0.06ppm Notes: |
| LI-7500A 75H-2180 | 2021-11-30 | Lab | Calibration | Lab | Last calibration: 2021-06-15 AGC=102.0 SDM=0 DAC1=- DAC2=- Ambient P=100.9kPa, Tair=27.0C, Tdew=12.3C Zero Air at 1400psi, AMP CA04119 524.77 at 1700 Tdewspan=20.0 CO2 zero 0.9138 -> 0.9136 Offset: -0.8ppm CO2 span 1.0281 -> 1.0295 Offset: -0.76ppm H2O zero 0.8901 -> 0.8924 Offset: 14.5ppm H2O span 1.0164 -> 1.0346 Offset: -0.39ppm Notes: Had to use config file from 2021-03-08 and enter latest zero and span values by hand. Had to add water to dew point generator. |
| LI-7700 TG1-0223 | 2021-12-01 | Mayberry Gas Analyzer CH4 | Calibration | Mayberry Gas Analyzer CH4 | Calibration Location: Mayberry
Last calibration: 2021-06-01 RSSI=85%, Optical RH=22% Ambient P=101.8kPa, Tair=9.3C Zero Air at 600psi, AMP CA04396 1.9317 at 1650 CH4 Zero Offset: 0.034ppm CH4 Span Offset: -0.0157ppm Notes: A lot of fog in the air so it was hard for RSSI to go >60 even when clean. The RSSI increased to 85 when we put the hood on. Relatively still day. After calibration, we dried down the sensor headspace with zero air until optics RH=10%. We swapped out the old drierite for fresh drierite. |
| miniDOT-usb 931528 | 2021-12-02 | Lab none | Installed | Hill Slough DO Sensor | I reinstalled the MiniDot that we removed yesterday due to dead batteries. |
| LI-7500A 75H-2182 | 2021-12-02 | Lab none | Installed | Vaira Gas Analyzer CO2/H2O | Installed at Vaira to replace sn 0042 for calibration. |
| LI-7500A 0042 | 2021-12-02 | Vaira Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Vaira for calibration. Replaced by sn 75H-2182. |
| LI-7500A 0073 | 2021-12-02 | Lab none | Installed | Tonzi-Floor Gas Analyzer CO2/H2O | Installed at Tonzi-Floor to replace sn 75H-2669 for calibration. |
| LI-7500A 75H-2669 | 2021-12-02 | Tonzi-Floor Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Tonzi-Floor for calibration. Replaced by sn 0073. |
| LI-7500A 75H-2180 | 2021-12-02 | Lab none | Installed | Tonzi-Tower Gas Analyzer CO2/H2O | Installed at Tonzi-Tower to replace sn 75H-2514 for calibration. |
| LI-7500A 75H-2514 | 2021-12-02 | Tonzi-Tower Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Tonzi-Tower for calibration. Replaced by sn 75H-2180. |
| LI-7500A 1594 | 2021-11-30 | Lab | Calibration | Lab | Last calibration: 2021-05-25 AGC=97.5 SDM=0 DAC1=- DAC2=- Ambient P=100.8kPa, Tair=27.6C, Tdew=12.7C Zero Air at 1350psi, AMP CA04119 524.77 at 1700 Tdewspan=20.0 CO2 zero 0.8648 -> 0.8645 Offset: -1.4ppm CO2 span 1.0136 -> 1.0128 Offset: 0.53ppm H2O zero 0.8861 -> 0.8877 Offset: 8.7ppm H2O span 1.005 -> 1.0045 Offset: 0.01ppm Notes: |
| LI-7500A 0073 | 2021-11-30 | Lab | Calibration | Lab | Last calibration: 2021-10-16 AGC=99.7 SDM=0 DAC1=- DAC2=- Ambient P=100.96kPa, Tair=25.3C, Tdew=10.6C Zero Air at 1400psi, AMP CA04119 524.77 at 1700 Tdewspan=20.0 CO2 zero 0.9182 -> 0.9175 Offset: -2.7ppm CO2 span 1 -> 1.0 Offset: -0.47ppm H2O zero 0.8187 -> 0.8174 Offset: -7ppm H2O span 1.0094 -> 1.0192 Offset: 0.22ppm Notes: This is the first lab calibration since refurbishment and factory calibration at Licor. I entered the new coefficients by hand. The dew point generator was acting funky again. I added water and it seemed better. The offsets were relatively good for a unit freshly returned from the factory. |
| LI-7550 AIU-0614 | 2021-11-30 | Lab none | Upgrade | Lab none | This interface box has been in the lab for a while. We need to swap out the box at Mayberry that might have been damaged by bad power. I loaded and old Mayberry config file. Then updated the firmware from v8.5.0 to v8.8.32. There is a newer v8.9.0 firmware, but I'm not sure if it is worth updating all of our sites yet. |
| LI-7500A 0073 | 2021-10-16 | Lab none | Calibration | Lab none | Last calibration: 2021-08-31
AGC=100 SDM=0 DAC1=- DAC2=- Ambient P=99kPa, Tair=99C, Tdew=99C Licor at psi, Licor 750 at 99 Tdewspan=12 CO2 zero 0.957 -> 0.9182 Offset: 0ppm CO2 span 1.0075 -> 1.0 Offset: 0ppm H2O zero 0.7337 -> 0.8187 Offset: 0ppm H2O span 1.0078 -> 1.0094 Offset: 0ppm Notes: Factory calibration at Licor after replacement of chopper, detector and source. Unknown ambient conditions and offsets. This sensor was sent to Licor because its signal was noisy. Its parts are almost 20 years old so I asked to have it renovated. Licor said, "Inspected the unit and found it in operational condition. Replaced the chopper motor, the detector and the light source. Subjected the unit to environmental tests and calibration." Should be nearly as good as new. |
| LI-7700 TG1-0223 | 2021-11-23 | Mayberry Gas Analyzer CH4 | Upgrade | Mayberry Gas Analyzer CH4 | Upgraded the firmware from v1.0.27 to v1.0.29. The sensor restarted succesfully and all seems well. |
| eosFD FD20180047 | 2021-11-23 | Mayberry Forced Diffusion Boom | Removed | Lab none | Removed from MB floating boom and brought back to the lab for testing. It underwent a lot of power cycles because of a short in the system and I want to test it before we deploy it again. |
| HMP45A U2120013 | 2021-11-23 | Mayberry RH & Temp | Removed | Lab none | Removed from MB and brought back to the lab for testing. AirT has been drifting downward since late October.It was replaced by HMP155 sn T2820180. |
| HMP45AC T1250012 | 2021-11-18 | Lab none | Installed | Bouldin Alfalfa none | Installed on BA tower for an HMP45 intercomparison with the tower HMP155. |
| HMP45AC U3030041 | 2021-11-18 | Lab none | Installed | Bouldin Alfalfa none | Installed on BA tower for an HMP45 intercomparison with the tower HMP155. |
| HMP155 T2820180 | 2021-11-18 | Cal Kit RH & Temp | Removed | Lab none | Removed from BA tower at the conclusion of the HMP155 intercomparison. |
| HMP155 T2820183 | 2021-11-18 | Bouldin Alfalfa | Removed | Lab none | Removed from BA tower at the conclusion of the HMP155 intercomparison. |
| HMP155 T2930114 | 2021-11-18 | Bouldin Alfalfa | Removed | Lab none | Removed from BA tower at the conclusion of the HMP155 intercomparison. |
| TE525MM 65560-615 | 2021-11-18 | Bouldin Alfalfa Precipitation | Calibration | Bouldin Alfalfa Precipitation | We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 52 tips and I adjusted both set screws 1 turn CCW. |
| TE525MM 65548-615 | 2021-11-18 | Bouldin Corn Precipitation | Calibration | Bouldin Corn Precipitation | I adjusted the screw 1 turn CCW before testing b/c I forgot to adjust it after the previous test. We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 49 tips and I called it good until next year. |
| PA-II-SD 68c63acc07a9 | 2021-11-18 | Bouldin Corn Air Quality Sensor | Removed | Lab none | Removed from BC tower and brought back to the lab because there was some corrosion on the SD card slot |
| eosFD FD20180068 | 2021-11-17 | Vaira Forced Diffusion West | Removed | Lab none | Removed from Vaira West due to bad CO2 concentration readings |
| SP75 020854E-6-03-02-06905 | 2021-11-12 | Lab none | Loaned | Loaned none | Loaned to Adina Paytan at UCSC for temporary setup on the Yampah Marsh at Elkhorn Slough. |
| SP75 020854E-6-03-02-06862 | 2021-11-12 | Lab none | Loaned | Loaned none | Loaned to Adina Paytan at UCSC for temporary setup on the Yampah Marsh at Elkhorn Slough. |
| PS-30M 186580399 | 2021-11-12 | Lab none | Loaned | Loaned none | Loaned to Adina Paytan at UCSC for temporary setup on the Yampah Marsh at Elkhorn Slough. |
| HMP155 T2820183 | 2021-09-03 | Lab none | Installed | Bouldin Alfalfa none | Installed on the BA bouncer tower for the advection experiment in the lower T/RH location |
| TE525MM 65548-615 | 2021-11-05 | Bouldin Corn Precipitation | Tested | Bouldin Corn Precipitation | We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 52 tips but forgot to adjust the screws. |
| HMP155 T2930114 | 2021-11-05 | Bouldin Alfalfa | Moved | Bouldin Alfalfa none | Removed from main tower (lower position) at the conclusion of this year's advection experiment and installed on the main tower for an HMP intercomparison |
| S2-411 1050 | 2021-11-05 | Cal Kit Narrow Band NDVI Reflected | Removed | Lab none | Removed from BA tower at the conclusion of the rad calibration and brought back to the lab. |
| S2-411 1049 | 2021-11-05 | Cal Kit Narrow Band NDVI Incoming | Removed | Lab none | Removed from BA tower at the conclusion of the rad calibration and brought back to the lab. |
| PAR-LITE 060831 | 2021-11-05 | Cal Kit PAR Sensor Incoming | Removed | Lab none | Removed from BA tower at the conclusion of the rad calibration and brought back to the lab. This sensor will go back to AMP. |
| CNR4 121038 | 2021-11-05 | Cal Kit Net Radiometer 4-way | Removed | Lab none | Removed from BA tower at the conclusion of the rad calibration and brought back to the lab. This sensor will go back to AMP. |
| WM 1590 152601 | 2021-11-05 | Bouldin Alfalfa-ADEX Anemometer Main Lower | Removed | Lab none | Removed from main tower (lower position) and brought back to the lab at the conclusion of this year's advection experiment |
| HMP155 T2820183 | 2021-11-05 | Bouldin Alfalfa none | Moved | Bouldin Alfalfa none | Removed from bouncer tower (lower position) at the conclusion of this year's advection experiment and installed on the main tower for an HMP intercomparison |
| WM 1590 153805 | 2021-11-05 | Bouldin Alfalfa-ADEX Anemometer Bouncer Lower | Removed | Lab none | Removed from bouncer tower (lower position) and brought back to the lab at the conclusion of this year's advection experiment |
| HMP155 T2820180 | 2021-11-05 | Bouldin Alfalfa-ADEX RH & Temp Bouncer Upper | Moved | Cal Kit RH & Temp | Removed from bouncer tower (upper position) at the conclusion of this year's advection experiment and installed on the main tower for an HMP intercomparison |
| WM 1590 152603 | 2021-11-05 | Bouldin Alfalfa-ADEX Anemometer Bouncer Upper | Removed | Lab none | Removed from bouncer tower (upper position) and brought back to the lab at the conclusion of this year's advection experiment |
| CNR4 120788 | 2021-11-08 | Borrowed none | Received | Lab none | Sebastien of AMP dropped this off today as an exchange for an older 4-way radiometer reference sensor, sn 121038. Came with a mounting rod and cables only. |
| PQS 1 212225 | 2021-11-08 | Borrowed none | Received | Lab none | Sebastien of AMP dropped this off in exchange for an older reference PAR, sn 060831. It came in its own box and a rubber cap over the sensor. |
| CNR4 121038 | 2021-11-08 | Lab none | Returned | Returned none | Returned to Sebastien of AMP in exchange for a freshly calibrated 4-way radiometer CNR4 sn 120788 |
| PAR-LITE 060831 | 2021-11-08 | Lab none | Returned | Returned none | Returned to Sebastien of AMP in exchange for a freshly calibrated reference PAR sn 212225 |
| TR-5251 40415-1006 | 2021-11-04 | Mayberry Precipitation | Adjusted | Mayberry Precipitation | Tested tipping bucket - got 53/50 tips. Adjusted screws 1/2 turn out (CCW). |
| GP-001 GP20160127 | 2021-11-04 | Lab none | Installed | Hill Slough CO2 Probe | Installed near the miniDot on the SW corner of the platform. This sensor floats so that the sensor window is about 10cm below the water surface. There is enough slack in the cable so it can go down some more with a lower tide, but hard to say where it will be with higher tides. |
| miniDOT-usb 931528 | 2021-11-04 | Lab none | Installed | Hill Slough DO Sensor | Installed on a yellow chain near the SW corner of the platform. I think the sensor window is about 10cm above the ground |
| TE525 48130-611 | 2021-11-04 | Hill Slough Precipitation | Adjusted | Hill Slough Precipitation | The screws were adjusted 1/2 turn in (CW) before testing. The test got 51/50 tips - okay. |
| LI-190/R Q100420 | 2021-10-21 | Lab none | Installed | Mayberry PAR Sensor Diffuse PAR | Installed as part of the rotating shadow band for diffuse PAR - not working until 11-04 |
| CR10X 35474 | 2021-10-21 | Lab none | Installed | Mayberry Data Logger Diffuse PAR | Installed to measure diffuse PAR from rotating shadow band. |
| LI-7500A 0418 | 2021-10-21 | Mayberry Gas Analyzer CO2/H2O | Adjusted | Mayberry Gas Analyzer CO2/H2O | Rest SS from 104 to 100 after cleaning |
| LI-7500A 0073 | 2021-09-08 | Lab none | Shipped | Factory none | Shipped to Licor for renovation. The signal is noisy and I have asked for its chopper, detector and light source to be replaced as these parts are about 20 years old. |
| LI-7500A 0073 | 2021-11-03 | Factory none | Returned | Lab none | Returned to the lab from revamp and calibration at Licor. |
| LI-7500A 0065 | 2021-10-21 | Gilbert Tract Gas Analyzer CO2/H2O | Adjusted | Gilbert Tract Gas Analyzer CO2/H2O | Reset signal strength from 108 to 100 |
| SP75 020854E-6-03-02-06862 | 2021-10-26 | Vaira Solar Panel SoilCO2-B | Removed | Lab none | Removed from Vaira - not in use, was for old soil co2 system. |
| SP75 020854E-6-03-02-06905 | 2021-10-26 | Vaira Solar Panel SoilCO2-A | Removed | Lab none | Removed from Vaira - not in use, was for old soil co2 system. |
| SP75 020854E-6-03-02-06862 | 2012-02-16 | Lab none | Installed | Vaira Solar Panel SoilCO2-B | Installed to provide 24V power for soil CO2 system but mistakenly wired for 12V - fixed on 3/19 |
| SP75 020854E-6-03-02-06905 | 2012-02-16 | Lab none | Installed | Vaira Solar Panel SoilCO2-A | Installed to provide 24V power for soil CO2 system but mistakenly wired for 12V - fixed on 3/19 |
| SP75 020854E-6-03-02-06862 | 2012-02-09 | Tonzi Solar Panel Floor H | Removed | Lab none | Removed from the Floor solar system. This panel has not been connected to the system since at least August 2008 |
| SP75 020854E-6-03-02-06905 | 2012-02-09 | Tonzi Solar Panel Floor G | Removed | Lab none | Removed from the Floor solar system. This panel has not been connected to the system since at least August 2008 |
| TE525MM 65560-615 | 2021-10-21 | Bouldin Alfalfa Precipitation | Tested | Bouldin Alfalfa Precipitation | We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 54 tips and adjusted its set screws 1.5 turns CCW (1/2 turn of both screws is a 2-3% adjustment). |
| TE525MM 65548-615 | 2021-10-21 | Bouldin Corn Precipitation | Tested | Bouldin Corn Precipitation | We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 54 tips and adjusted its set screws 1.5 turns CCW (1/2 turn of both screws is a 2-3% adjustment). |
| TR-525M 50229-112 | 2021-10-21 | East End Precipitation | Tested | East End Precipitation | We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 54 tips and adjusted its set screws 1.5 turns CCW (1/2 turn of both screws is a 2-3% adjustment). |
| TR-5251 40415-1006 | 2021-10-21 | Mayberry Precipitation | Tested | Mayberry Precipitation | We dripped 240ml of water through the bucket using a peristaltic pump powered with a lithium battery. This should result in 50 tips in about 20 minutes. We got 54 tips and adjusted its set screws 1.5 turns CCW (1/2 turn of both screws is a 2-3% adjustment). |
| S2-411 1050 | 2021-10-21 | Cal Kit Narrow Band NDVI Reflected | Moved | Cal Kit Narrow Band NDVI Reflected | Moved from GT to BA as part of the radiometer cal kit to begin the calibration at BA |
| S2-411 1049 | 2021-10-21 | Cal Kit Narrow Band NDVI Incoming | Moved | Cal Kit Narrow Band NDVI Incoming | Moved from GT to BA as part of the radiometer cal kit to begin the calibration at BA |
| PAR-LITE 060831 | 2021-10-21 | Cal Kit PAR Sensor Reflected | Moved | Cal Kit PAR Sensor Incoming | Moved from GT Reflected to BA Incoming as part of the radiometer cal kit to begin the calibration at BA |
| CNR4 121038 | 2021-10-21 | Cal Kit Net Radiometer 4-way | Moved | Cal Kit Net Radiometer 4-way | Moved from GT to BA as part of the radiometer cal kit to begin the calibration at BA |
| CR1000 23865 | 2021-10-21 | Cal Kit Data Logger | Moved | Cal Kit Data Logger | Moved from GT to BA as part of the radiometer cal kit to begin the calibration at BA |
| miniDOT 1221 | 2021-10-20 | Lab none | Tested | Lab none | This sensor was covered in barnacles, the copper screen was falling apart and there are nicks in the coating on the window. I cleaned up the sensor and tested it side by side with miniDot sn 931528. Both sensors were suspended in a bucket of water with a bubbler in the bottom. The sensors were out of the stream of bubbles. Ice was added to the water bringing its temperature down from 20C to 0C. Then the dissolved O2 was recorded by both sensor over about 24 hours as the water returned to room temperature. The two miniDots matched each other by better then 2%. And they matched the theoretical O2 saturation of the water at about 4%. This sensor had a quailty flag of about 0.84 whereas the newer, uncompromised sensor (sn 931528) had a quality flag on 1.03. I think I'll send a photo of the window coating and these notes to PME to get their take, but I think it's okay to return sn 1221 to service. |
| miniDOT-usb 899502 | 2021-09-02 | Lab none | Installed | Mayberry DO Sensor D | Installed at Mayberry to replace sn 1221 that was covered with barnacles. |
| miniDOT 1221 | 2021-09-02 | Mayberry DO Sensor D | Removed | Lab none | Removed from Mayberry because it had a bunch of barnacles growing on it, the copper screen was disintegrating and the coating on the window looked damage. Replaced by sn 899502 |
| ML2x 139/052 | 2021-03-17 | Lab none | Calibration | Lab none | After looking at the data recorded from 2021-03-17 to 2021-10-06 it seemed that this probe was reading too low in the spring and too high in the fall. Most years the soil gets completely saturated in the spring and completely dry in the fall. If you take the max and min values from all years they are very similar. Min: 473mV STDEV=6.8mV, Max: 913mV STDEV 24.8. Then we can use these to scale this sensor's min and max with this year's data and we get Corrected (mV) = raw (mV) * 1.272 -187.73 And using the manual's default conversion values for mineral soil (0.05 and -5), the total conversion is: %m = mV * 0.636 + 4.39 |
| CNR4 160848 | 2019-10-21 | Lab none | Returned | Returned none | Robert returned it to Stephen around 2019-10-21 when Robert went to LBL for the weekly NGEE Tropics meeting |
| LI-7500A 0065 | 2021-09-15 | Lab none | Installed | Gilbert Tract Gas Analyzer CO2/H2O | Installed at Gilbert Tract to replace sn 0041 for calibration. |
| LI-7500A 0041 | 2021-09-15 | Gilbert Tract Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Gilbert Tract for calibration. Replaced by sn 0065. |
| GP-001 GP20200089 | 2021-09-09 | Lab none | Installed | Gilbert Tract CO2 Probe | Installed at Gilbert Tract but the cable was too short - not hooked up until 2021-09-15 |
| miniDOT-usb 906606 | 2021-09-09 | Lab none | Installed | Gilbert Tract DO Sensor | Installed at Gilbert Tract on a yellow chain that just barely meets the water. When the site becomes tidal we will have to have a longer chain or more likely a boardwalk to reach deeper water. |
| HFP01 11329 | 2021-09-09 | Lab none | Installed | Gilbert Tract Heat Flux Plate C | Installed at Gilbert Tract at -2cm to the west of the tower |
| HFP01 11328 | 2021-09-09 | Lab none | Installed | Gilbert Tract Heat Flux Plate B | Installed at Gilbert Tract at -2cm to the northwest of the tower |
| HFP01 11325 | 2021-09-09 | Lab none | Installed | Gilbert Tract Heat Flux Plate A | Installed at Gilbert Tract at -2cm to the southwest of the tower |
| TE525MM 65552-615 | 2021-09-15 | Lab none | Installed | Gilbert Tract Precipitation | Installed at Gilbert Tract on the northeast corn of the scaffolding. |
| miniDOT-usb 906606 | 2021-09-02 | Sherman Wetland DO Sensor | Removed | Lab none | Removed from Sherman Wetland with the decommissioning of the site. |
| HFP01 11329 | 2021-09-02 | Sherman Wetland Heat Flux Plate B | Removed | Lab none | Removed from Sherman Wetland with the decommissioning of the site. The aluminum conduit was rotting and needed to be removed. |
| HFP01 11328 | 2021-09-02 | Sherman Wetland Heat Flux Plate A | Removed | Lab none | Removed from Sherman Wetland with the decommissioning of the site. The aluminum conduit was rotting and needed to be removed. |
| HFP01 11325 | 2021-09-02 | Sherman Wetland Heat Flux Plate C | Removed | Lab none | Removed from Sherman Wetland with the decommissioning of the site. The aluminum conduit was rotting and needed to be removed. |