Equipment and Calibration History
Page: 1 2 3 4 5 6 7 [8] 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65| Ser No. | Date | Loc From | Title | Loc To | Notes |
|---|---|---|---|---|---|
| GMT221 G0150035 | 2022-10-05 | Tonzi-SoilCO2 CO2 Probe Tree1 Profile -0.04 | Removed | Lab none | The soil co2 gradient system has not been in good condition for a long time. Finally getting around to removing the equipment from the field: Tree1 -4cm |
| GMM222 L2010069 | 2022-10-05 | Tonzi-SoilCO2 CO2 Probe Tree1 Profile -0.02 | Removed | Lab none | The soil co2 gradient system has not been in good condition for a long time. Finally getting around to removing the equipment from the field: Tree1 -2cm |
| CR23X 2301 | 2022-10-05 | Tonzi Data Logger Soil CO2 | Removed | Lab none | The soil co2 gradient system has not been in good condition for a long time. Finally getting around to removing the equipment from the field. |
| SX20U C1031127-2306254 | 2022-08-24 | Lab none | Installed | Hill Slough none | Installed with a CR23X and lithium battery at the Hill Slough channel to collect data from water sensors installed in the channel |
| GP-001 GP20160127 | 2022-08-24 | Hill Slough CO2 Probe | Moved | Hill Slough CO2 Probe | Moved from the Hill Slough main tower to the channel about 40m east of the main tower. At the tower, the sensor was above water during low tide so we moved the sensor into deeper water where it will remain submerged during low tide. |
| CTD-10 1782503941 | 2022-08-24 | Hill Slough Water Level | Moved | Hill Slough Water Level | Moved from the Hill Slough main tower to the channel about 40m east of the main tower. At the tower, the sensor was above water during low tide so we moved the sensor into deeper water where it will remain submerged during low tide. |
| CR23X 2301 | 2002-06-20 | Lab none | Installed | Tonzi Data Logger Soil CO2 | Installed with the initiation of soil CO2 gradient measurements |
| CR23X 2071 | 2018-10-11 | Lab none | Returned | Returned none | Returned to Robin in Allen Goldstein's lab |
| miniDOT-usb 931528 | 2022-10-05 | Lab none | Installed | Hill Slough DO Sensor | Installed after cleaning and measurement check in the lab. |
| EXO pH-ORP 22D102641 | 2022-09-29 | Lab none | Installed | Hill Slough pH-ORP Channel | Installed as part of the EXO2 sonde in the channel at Hill Slough. |
| EXO fDOM 22E100649 | 2022-09-29 | Lab none | Installed | Hill Slough fDOM Channel | Installed as part of the EXO2 sonde in the channel at Hill Slough. |
| EXO Turbidity 22E106072 | 2022-09-29 | Lab none | Installed | Hill Slough Turbidity Channel | Installed as part of the EXO2 sonde in the channel at Hill Slough. |
| EXO pH-ORP 22D102641 | 2022-09-16 | Hill Slough pH-ORP Channel | Removed | Lab none | Removed as part of the EXO2 channel deployed in the channel at HS. Brought back to the lab for cleaning and calibration. |
| EXO fDOM 22E100649 | 2022-09-16 | Hill Slough fDOM Channel | Removed | Lab none | Removed as part of the EXO2 channel deployed in the channel at HS. Brought back to the lab for cleaning and calibration. |
| EXO Turbidity 22E106072 | 2022-09-16 | Hill Slough Turbidity Channel | Removed | Lab none | Removed as part of the EXO2 sonde deployed in the channel at HS. Brought back to the lab for cleaning and calibration. |
| EXO pH-ORP 22D102641 | 2022-07-13 | Lab none | Installed | Hill Slough pH-ORP Channel | Installed as part of the EXO2 sonde at HS in the channel off of the boardwalk, about 30m east of the tower. |
| EXO fDOM 22E100649 | 2022-07-13 | Lab none | Installed | Hill Slough fDOM Channel | Installed as part of the EXO2 sonde at HS in the channel off of the boardwalk, about 30m east of the tower. |
| EXO Turbidity 22E106072 | 2022-07-13 | Lab none | Installed | Hill Slough Turbidity Channel | Installed as part of the EXO2 sonde at HS in the channel off of the boardwalk, about 30m east of the tower. |
| miniDOT-usb 931528 | 2022-09-29 | Hill Slough DO Sensor | Removed | Lab none | Removed from the HS channel and brought back to the lab for cleaning. There are calcareous deposits (some sort of encrusting worm) on and around the sensing foil. I soaked it in distilled white vinegar for 3 days. The deposits came off easily with a soft toothbrush. I rinsed the sensor well under DI water. |
| EXO2 22C103416 | 2022-09-29 | Lab none | Installed | Hill Slough Water Level | Installed in the channel at Hill Slough. The sonde is now wired to the CR23X, which queries it for data every 10sec. The sonde is measureing and storing data internally every 5min. |
| HMP45AC W0510026 | 2011-02-03 | Tonzi | Removed | Lab none | Removed from under the trees near the floor tower. |
| NR-LITE 041556 | 2010-03-16 | Lab none | Installed | Tonzi none | Installed at the request of Hideki in an unshaded opening near the east end of the radiation tram. |
| EXO2 22C103416 | 2022-09-16 | Hill Slough | Removed | Lab none | Removed from the channel at Hill Slough. It was brought back to the lab for cleaning, calibration, and to convert its output to SDI-12 so we can wire it to the channel CR23X. |
| LI-7500A 75H-2667 | 2022-09-15 | Lab none | Installed | East End Gas Analyzer CO2/H2O | Installed at East End to replace sn 0041 for calibration. |
| LI-7500A 0041 | 2022-09-15 | East End Gas Analyzer CO2/H2O | Removed | Lab none | Removed from East End for calibration. Replaced by sn 75H-2667. |
| LI-7500A 0035 | 2022-09-15 | Lab none | Installed | West Pond Gas Analyzer CO2/H2O | Installed at West Pond to replace sn 0073 for calibration. |
| LI-7500A 0073 | 2022-09-15 | West Pond Gas Analyzer CO2/H2O | Removed | Lab none | Removed from West Pond for calibration. Replaced by sn 0035. |
| S2-411 1050 | 2022-09-15 | Gilbert Tract | Removed | Lab none | Removed from GT tower after 1 month of intercomparison with the SRS NDVI sensors |
| S2-411 1049 | 2022-09-15 | Gilbert Tract | Removed | Lab none | Removed from GT tower after 1 month of intercomparison with the SRS NDVI sensors |
| LI-7500A 0065 | 2022-09-14 | Lab none | Installed | Vaira Gas Analyzer CO2/H2O | Installed at Vaira to replace sn 75H-2667 for calibration. |
| LI-7500A 75H-2667 | 2022-09-14 | Vaira Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Vaira for calibration. Replaced by sn 0065. |
| CR23X 2143 | 2022-08-10 | Lab none | Installed | Experiment none | Installed on the back of Robert's e-bike for his urban heat island transect in Oakley |
| LI-6400 PSC-0785 | 2022-09-13 | Borrowed none | Returned | Lab none | LI-6400, all components, and batteries were returned from Rizwan. |
| HFP01 000139 | 2001-01-05 | Lab none | Installed | Tonzi Heat Flux Plate B | Likely first installation date and location estimated from notes and data. |
| HFP01 000138 | 2001-01-05 | Lab none | Installed | Tonzi Heat Flux Plate A | Likely first installation date and location estimated from notes and data. |
| HFP01 000140 | 2001-01-05 | Lab none | Installed | Tonzi Heat Flux Plate C | Likely first installation date and location estimated from notes and data. |
| HFP01 000144 | 2001-01-05 | Lab none | Installed | Tonzi Heat Flux Plate E | Likely first installation date and location estimated from notes and data. |
| HFP01SC 00068 | 2001-01-05 | Lab none | Installed | Tonzi Heat Flux Plate D | Likely first installation date and location estimated from notes and data. |
| LI-7500A 0418 | 2022-09-12 | Lab | Calibration | Lab | Last calibration: 2022-08-30 AGC=94.7 SDM=0 DAC1=- DAC2=- Ambient P=100.4kPa, Tair=21.8C, Tdew=15.1C Zero Air at 1900psi, AMP CA04119 524.77 at 1400 Tdewspan=20.0 CO2 zero 0.9082 -> 0.9086 Offset: 1.4ppm CO2 span 1.0000 -> 1.0050 Offset: -3.47ppm H2O zero 0.9313 -> 0.9317 Offset: 2.4ppm H2O span 1.0008 -> 1.0065 Offset: -0.12ppm Notes: This head had a drift of SS (and CO2, H2O) after refit by Licor in March. It was calibrated/tested in the lab several times in August. Full calibration on 8/30 but not all the information written down. 8/30 coefficients entered as 'existing' and it seems stable since then. We will try it in the field again. |
| LI-7500A 0065 | 2022-09-12 | Lab | Calibration | Lab | Last calibration: 2022-04-08 AGC=101.0 SDM=0 DAC1=- DAC2=- Ambient P=100.4kPa, Tair=22.8C, Tdew=15.2C Zero Air at 1900psi, AMP CA04119 524.77 at 1400 Tdewspan=20.0 CO2 zero 0.8908 -> 0.8918 Offset: 4.5ppm CO2 span 1.0198 -> 1.0227 Offset: -1.97ppm H2O zero 0.7308 -> 0.7316 Offset: 6.7ppm H2O span 1.016 -> 1.0167 Offset: -0.01ppm Notes: |
| SRS-Pi PRI 913003012 | 2022-09-12 | Lab none | Tested | Lab none | Tested in the lab with the lab CR1000. Could not connect to datalogger when this sensor was plugged in, even though the datalogger works with other sensors. This sensor is bad and probably not repairable. |
| S2-411 1054 | 2022-09-12 | Lab none | Tested | Lab none | Plugged in to a CR1000 in the lab but 650out is still bad. It's stuck at about -3.7. |
| SRS-Pi PRI 913003012 | 2022-08-31 | Bouldin Alfalfa Narrow Band PRI Incoming | Removed | Lab none | Removed from the BA main tower because it was shorting out the whole met system. Brought back to the lab. |
| RPI0W RPI0W-002 | 2022-08-31 | Bouldin Corn Camera C | Removed | Lab none | Removed this zcam from BC and brought back to the lab since the corn canopy has finished development and we won't get any more interesting photos |
| LI-7500A 75H-2180 | 2022-08-31 | Lab none | Installed | Bouldin Corn Gas Analyzer CO2/H2O | Installed at Bouldin Corn to replace sn 0065 for calibration. |
| LI-7500A 0065 | 2022-08-31 | Bouldin Corn Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Corn for calibration. Replaced by sn 75H-2180. |
| LI-7500A 75H-2180 | 2022-08-30 | Mayberry Gas Analyzer CO2/H2O | Removed | Lab none | Removed from MB and brought back to the lab for calibration. It was replaced by sn 75H-2514. |
| LI-7500A 75H-2514 | 2022-08-30 | Lab none | Installed | Mayberry Gas Analyzer CO2/H2O | Installed at Mayberry to replace sn 75H-2180 for calibration. |
| S2-411 1054 | 2022-08-30 | East End Narrow Band NDVI Reflected B | Removed | Lab none | Removed from EE and brought back to the lab for testing. 650out data is bad. |
| S2-411 1053 | 2022-08-30 | East End Narrow Band NDVI Incoming B | Removed | Lab none | Removed from EE and brought back to the lab for testing. This sensor's data was ok but the outgoing(reflected) sensor sn 1054 data was weird, so I brought both sensors in. |
| RPI0W RPI0W-001 | 2022-06-08 | Bouldin Corn camera B | Removed | Lab none | This camera was dead. There was a puddle of water in the bottom of the enclosure and white corrosion all over the board and mini-USB connector. |
| RPI0W RPI0W-002 | 2022-05-27 | Lab none | Installed | Bouldin Corn Camera C | Installed between corn rows |
| RPI0W RPI0W-001 | 2022-05-27 | Lab none | Installed | Bouldin Corn camera B | Installed in line with a corn row. |
| LI-7500A 75H-2180 | 2022-08-30 | Lab | Calibration | Lab | Last calibration: 2022-03-30 AGC=100.2 SDM= DAC1= DAC2= Ambient P=100.5kPa, Tair=24.8C, Tdew=14.4C Zero Air at 275psi, AMP CA04119 524.77 at 1400 Tdewspan=20.00 CO2 zero 0.9141 -> 0.9148 Offset: 3.30ppm CO2 span 1.0373 -> 1.0318 Offset: 3.89ppm H2O zero 0.8911 -> .8916 Offset: 3.3ppm H2O span 1.0345 -> 1.0122 Offset: .49ppm Notes: The initial H2O Span at 20.00 made the sensor jump to 20.02, but another span a few minutes later was right on 20.00. Should be ok. |
| SD130BN 0030F4D214A4 | 2022-08-29 | Lab none | Shipped | Factory none | Shipped back to StarDot for inspection/repair. The green LED in front comes on when the camera is plugged into power, but there is no network activity no matter how I try to physically connect it (through a router, through a switch, directly through a computer; with every combination of laptop ethernet port IP address/subnet). The only exception is if I connect it directly to a laptop with a crossover cable--the camera ethernet port does have a green light blinks every 3 seconds, but there are no changes to the green light (i.e., no network activity) even when I start StarDot Tools. It seemed to boot fine after a hard reset, but there was still no network activity. This camera was set to the default 192.168.2.101 IP address and connected fine in the lab in the past. The camera stopped working after bringing it back from Elkhorn Slough field trip in mid July. |
| LI-7500A 75H-2182 | 2022-08-24 | Lab none | Shipped | Factory none | Shipped back to Licor for inspection and repair. Expected turnaround time is 2-3 months. |
| LI-7500A 75H-2176 | 2022-08-24 | Lab none | Installed | Hill Slough Gas Analyzer CO2/H2O | Installed at Hill Slough to replace sn 0035 for calibration. |
| LI-7500A 0035 | 2022-08-24 | Hill Slough Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Hill Slough for calibration. Replaced by sn 75H-2176. |
| CR23X 2299 | 2022-08-24 | Lab none | Installed | Hill Slough none | Installed with a solar panel and lithium battery at the Hill Slough channel. This datalogger will collect data from water sensors installed in the channel. |
| LI-7500A 0035 | 2022-08-25 | Lab none | Installed | Tonzi-Floor Gas Analyzer CO2/H2O | Installed at Tonzi-Floor to replace sn 75H-2514 for calibration |
| BB-Fab BB-TZ_soilco2 | 2022-08-25 | Tonzi Battery Bank soil co2 | Maintenance | Tonzi Battery Bank soil co2 | This battery bank had been without batteries since its batteries were moved to the Tower a few weeks ago. I installed three old batteries from the Floor system that tested ok with the load tester. I rewired the two larger solar panels to 12V. The two smaller panels had there leads chewed and I left them disconnected for now. |
| LI-7500A 75H-2514 | 2022-08-25 | Tonzi-Floor Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Tonzi-Floor for calibration. Replaced by sn 0035. |
| LI-7500A 75H-2669 | 2022-08-25 | Lab none | Installed | Tonzi-Tower Gas Analyzer CO2/H2O | Installed at Tonzi-Tower to replace sn 0418 for calibration. |
| LI-7500A 0418 | 2022-08-25 | Tonzi-Tower Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Tonzi-Tower for calibration. Replaced by sn 75H-2669. |
| BB-Fab BB-TF | 2022-08-25 | Tonzi-Floor Battery Bank | Maintenance | Tonzi-Floor Battery Bank | The four existing batteries have been dying as soon as it gets dark. These were replaced with the four good batteries from the Tower installed in a new action packer box. The solar panel wiring was also checked but no issues found. Three of the old batteries tested okay and were moved to the Soil CO2 system. The one old battery that tested weak with the load tester was returned for its lead. |
| BB-Fab BB-TT | 2022-08-25 | Tonzi-Tower Battery Bank | Maintenance | Tonzi-Tower Battery Bank | Six new Duracell deep cycle AGM batteries were installed in two new action packers. Four good batteries were moved to the Floor and the rest of the 12 dead batteries turned in for their lead. |
| CTD-10 1782303006 | 2022-08-24 | Gilbert Tract | Removed | Lab none | Removed from GT and brought back to the lab. The depth data is bad but temperature and conductivity seemed reasonable. |
| LI-7500A 0035 | 2022-08-25 | Lab | Calibration | Lab | Last calibration: 2022-04-19 AGC=99.1 SDM=0 DAC1=- DAC2=- Ambient P=100.3kPa, Tair=20.5C, Tdew=13.9C Zero Air at 300psi, AMP CA04119 524.77 at 1400 Tdewspan=18.0 CO2 zero 0.9372 -> 0.9374 Offset: 0.7ppm CO2 span 1.0167 -> 1.0234 Offset: -4.57ppm H2O zero 0.8983 -> 0.8995 Offset: 7.4ppm H2O span 1.031 -> 1.0334 Offset: -0.05ppm Notes: |
| LI-7500A 75H-2669 | 2022-08-23 | Lab | Calibration | Lab | Last calibration: 2021-12-09 AGC=95.8 SDM= DAC1= DAC2= Ambient P=100kPa, Tair=26.03C, Tdew=16.96C Zero Air at 300psi, AMP CA04119 524.77 at 1400 Tdewspan=20.00 CO2 zero 0.9186 -> .9188 Offset: .94ppm CO2 span 1.0133 -> 1.0083 Offset: 3.8ppm H2O zero 0.9008 -> .9040 Offset: 20.6ppm H2O span 1.0123 -> 1.0174 Offset: -.11ppm Notes: Calibration using AMP loaner 7550 sn AIU-1039 |
| LI-7500A 75H-2176 | 2022-08-23 | Lab | Calibration | Lab | Last calibration: 2022-04-19 AGC=96.3 SDM= DAC1= DAC2= Ambient P=100.1kPa, Tair=24.01C, Tdew=14.55C Zero Air at 300psi, AMP CA04119 524.77 at 1400 Tdewspan=20.00 CO2 zero 0.867 -> .8678 Offset: 3.56ppm CO2 span 1.0081 -> 1.0008 Offset: 4.59ppm H2O zero 0.8557 -> .8537 Offset: -11.9ppm H2O span 0.9228 -> .923 Offset: -.02ppm Notes: Calibration using AMP loaner 7550 sn AIU-1039 |
| eosFD 20160002 | 2018-01-17 | Lab none | Returned | Factory none | Sent by Fedex to Gregory Maurer (UCB) currently at UNM Albuquerque for Eosense. |
| eosFD 20160003 | 2018-01-17 | Lab none | Returned | Factory none | Sent by Fedex to Gregory Maurer (UCB) currently at UNM Albuquerque for Eosense. |
| eosFD 20160004 | 2018-01-17 | Lab none | Returned | Factory none | Sent by Fedex to Gregory Maurer (UCB) currently at UNM Albuquerque for Eosense. |
| eosFD 20160005 | 2018-01-17 | Lab none | Returned | Factory none | Sent by Fedex to Gregory Maurer (UCB) currently at UNM Albuquerque for Eosense. |
| eosFD 20160006 | 2018-01-17 | Lab none | Returned | Factory none | Sent by Fedex to Gregory Maurer (UCB) currently at UNM Albuquerque for Eosense. |
| LI-7500A 75H-2418 | 2022-08-18 | Lab none | Installed | Gilbert Tract Gas Analyzer CO2/H2O | Installed on the GT tower to replace the one that failed a few days ago and was removed. |
| BB-Fab BB-TZ_soilco2 | 2022-08-05 | Tonzi Battery Bank soil co2 | Maintenance | Tonzi Battery Bank soil co2 | The batteried in this bank have been temporarily removed to power the Tower. Likely this bank will be repopulated to power the OSU-SP1 system and a couple FD chambers as the Vaisala soil CO2 system is decommissioned. |
| BB-Fab BB-TF | 2022-08-05 | Tonzi-Floor Battery Bank | Maintenance | Tonzi-Floor Battery Bank | This bank has been failing in the early morning. I disconnected all the batteries and they load tested okay. I added three gallons of DI to the four batteries. I shouted the south most to wiring them back up but they seemed okay. |
| BB-Fab BB-TT | 2022-08-05 | Tonzi-Tower Battery Bank | Maintenance | Tonzi-Tower Battery Bank | The batteries in this bank are completely dead - not even accepting charge at midday. These batteries were all disconnected and four batteries from the soil co2 system sn BB-TZ_soilco2 were temporarily swapped in. |
| LI-7500A 75H-2418 | 2022-08-17 | Lab | Calibration | Lab | Last calibration: 2020-03-23 AGC=100.5 SDM=0 DAC1=- DAC2=- Ambient P=100.2kPa, Tair=24.2C, Tdew=13.6C Zero Air at 300psi, AMP CA04119 524.77 at 1400 Tdewspan=20.0 CO2 zero -> 0.9786 Offset: -0.7ppm CO2 span 1.0091 -> 1.0054 Offset: 2.63ppm H2O zero 0.8245 -> 0.8242 Offset: 0.9ppm H2O span 1.0166 -> 1.0292 Offset: -0.28ppm Notes: Borrowed from Ameriflux. Previous cal values retrieved from instrument. Seems the 7500s don't drift much and that our cal methods match whatever methods were used last time. |
| S2-411 1050 | 2022-08-16 | Lab none | Installed | Gilbert Tract none | Installed at GT in the reflected position and data collected in a separate data table for an NDVI intercomparison. |
| S2-411 1049 | 2022-08-16 | Lab none | Installed | Gilbert Tract none | Installed at GT in the incoming position and data collected in a separate data table for an NDVI intercomparison. |
| LI-7500A 75H-2182 | 2022-08-16 | Gilbert Tract Gas Analyzer CO2/H2O | Removed | Lab none | Removed from GT because it was reading **.** and brought back to the lab for further testing. |
| SD130BN 0030F4D214A4 | 2022-03-31 | Mayberry | Removed | Lab none | Removed from Mayberry with the end of the camera inter-comparison |
| HFP01 003072 | 2022-08-04 | Lab none | Installed | Bouldin Alfalfa-ADEX Heat Flux Plate Bouncer A | Installed at the Bouncer tower at -10cm depth |
| SI-131 7385 | 2022-08-10 | Lab none | Installed | Experiment | Installed on the back of Robert's e-bike for his urban heat island transect in Oakley |
| LI-7500 0976 | 2022-08-10 | Lab none | Installed | Experiment | Installed on the back of Robert's e-bike for his urban heat island transect in Oakley |
| NR-LITE 990354 | 2022-08-10 | Lab none | Installed | Experiment | Installed on the back of Robert's e-bike for his urban heat island transect in Oakley |
| PAR-LITE 990025 | 2022-08-10 | Lab none | Installed | Experiment none | Installed on the back of Robert's e-bike for his urban heat island transect in Oakley |
| LI-7500 0976 | 2022-08-10 | Lab | Calibration | Lab | Last calibration: 2017-06-12 AGC=57 SDM=7 DAC1= DAC2= Ambient P=100.7kPa, Tair=25.8C, Tdew=15.3C Zero Air at 300psi, AMP CA04119 524.77 at 1425 Tdewspan=20.00 CO2 zero 0.8597 -> .8596 Offset: -.03ppm CO2 span 1.0077 -> 1.0102 Offset: 1.82ppm H2O zero 0.6335 -> .632 Offset: -10.5ppm H2O span 1.031 -> 1.0138 Offset: .37ppm Notes: Pulled out this old IRGA for Robert's UHI transect via ebike. The calibration was surprisingly good given we haven't used this sensor in 5 years. Calibrated using a small white eePC netbook using a Licor serial cable that plugs directly into the green terminal block inside the box. I had to set the span temperature in software to 19.91 in order for dew point value to be 20.00 after pressing "Span". |
| TEROS21 G20007096 | 2022-06-07 | Lab none | Installed | Tonzi Soil Water Potential C | Installed near the OSU-SP1 soil sensors at -10cm, vertical orientation |
| SoilVUE10 2688 | 2022-06-07 | Lab none | Installed | Tonzi Soil Moisture Probe J Profile | Installed near the OSU-SP1 soil sensors |
| SoilVUE10 2674 | 2022-06-07 | Lab none | Installed | Tonzi Soil Moisture Probe I Profile | I installed this probe to the west of the Floor met boxes near the existing Moisture Point probe and soil matrix sensor under the trees. |
| SoilVUE10 2676 | 2022-06-07 | Lab none | Installed | Tonzi Soil Moisture Probe H Profile | I installed this probe in the open to the south of the Floor met boxes towards the Tower along the existing power conduit. I cut a hole in the conduit and ran the cable back to the Floor CR23x. |
| eosFD FD20190027 | 2022-08-03 | Lab none | Tested | Lab none | I did two performance tests on this chamber. The CO2 for bother chambers is reading negative -200 to -300 ppm. I tried to reset it to 400ppm but it didn't seem to work. |
| eosFD FD20190027 | 2022-07-19 | Tonzi-SoilCO2 Forced Diffusion Open | Removed | Lab none | It was reading mostly zeros (with large positive and negative spikes) in the last few weeks, so it was removed and brought back to the lab for testing. |
| eosFD FD20180048 | 2022-04-27 | Lab none | Installed | Tonzi-SoilCO2 Forced Diffusion Open | Reinstalled at Tree 1 after testing in the lab. I had removed it because I thought it was broken but it might have been reading funny because it was lying on its side. It seemed okay in the lab. I installed it in a slightly different location with more litter on the soil surface. |
| TEROS21 G20010035 | 2022-04-27 | Lab none | Installed | Tonzi Soil Water Potential B | Installed near the base of a tree near the Tower Moisture Point Probe |
| TEROS21 G20007112 | 2022-04-27 | Lab none | Installed | Tonzi Water Potential A | Installed near the drip line of the trees near the Tower Moisture Point probe |
| EXO2 22C103416 | 2022-07-13 | Lab none | Installed | Hill Slough Water Level | Installed at HS in the channel off of the boardwalk, about 30m east of the tower. We installed the sonde near low tide to ensure it would stay underwater at all times. |