Equipment and Calibration History
Page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 [30] 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65| Ser No. | Date | Loc From | Title | Loc To | Notes |
|---|---|---|---|---|---|
| LI-7500A 75H-2182 | 2018-10-24 | Lab none | Calibration | Lab none | Last calibration: 2018-07-10 AGC=87.3 SDM=0 DAC1=0 DAC2=0 Ambient P=100.55kPa, Tair=26.87C, Tdew=12.61C Zero Air at 1500psi, AMP Air 408.97 at 1100 Tdewspan=16.00 CO2 zero 0.8841 -> .8844 Offset: 1.11ppm CO2 span 1.0168 -> 1.0188 Offset: -1.04ppm H2O zero 0.845 -> .8449 Offset: -.6ppm H2O span 1.0202 -> 1.0143 Offset: .13ppm Notes: |
| LI-7500A 75H-2150 | 2018-10-24 | Lab none | Calibration | Lab none | Last calibration: 2018-07-10 AGC=97.5 SDM=0 DAC1=0 DAC2=0 Ambient P=100.6kPa, Tair=26.7C, Tdew=11.95C Zero Air at 1500psi, AMP Air 408.97 at 1100 Tdewspan=16.00 CO2 zero 0.9017 -> .9021 Offset: 1.86ppm CO2 span 1.002 -> 1.0050 Offset: -1.74ppm H2O zero 0.8662 -> .8660 Offset: -1.9ppm H2O span 1.0069 -> 1.0069 Offset: 0.00ppm Notes: No change in H2O span. |
| LI-7700 TG1-0424 | 2018-10-24 | Lab none | Calibration | Lab none | Calibration Location: Lab Last calibration: 2018-04-13 RSSI=82.9%, Optical RH=9% Ambient P=100.6kPa, Tair=27.8C Zero Air at 1500psi, AMP CH4 1.9497 at 1150 CH4 Zero Offset: -0.015ppm CH4 Span Offset: 0.043ppm Notes: First calibration after replacing power board - no problems found. |
| LI-7700 TG1-0424 | 2018-10-22 | Lab none | Upgrade | Lab none | I swapped out power board pn 9677-079 per Licor's instructions. According to Licor the original boards Rev 0, could be damaged by exposure to voltage above 24VDC. The new board Rev 0A (V3) should not have that problem. |
| TE525MM 49187-109 | 2018-10-18 | Sherman Barn Precipitation | Calibration | Sherman Barn Precipitation | Got 94 of 100 tips - adjusted by a total of 3.5 turns CCW (screws were loose, so this total is suspicious; should have been a CW adjustment when all was said and done)
2018-10-18: Got 94 of 100 tips - adjusted by 0.5 turns CW. 2018-12-18: Got 117 of 100 tips - adjusted by 1 turn CCW, but screws feel very loose. 2019-01-03: Got 118 of 100 tips - adjusted by 3 turns CCW. (previous adjustment of 1 turn CCW did not seem to make a difference). 2019-01-24: Got 100 of 100 tips! No adjustments made. |
| LI-7500A 75H-2669 | 2018-10-18 | Lab none | Installed | Sherman Barn Gas Analyzer CO2/H2O | Installed on Sherman Barn to replace sn 0041 for calibration |
| LI-7500A 0041 | 2018-10-18 | Sherman Barn Gas Analyzer CO2/H2O | Removed | Lab Gas Analyzer CO2/H2O | Removed from Sherman Barn for calibration. Replaced by sn 75H-2669. |
| GP-001 GP20140016 | 2018-10-18 | Sherman Wetland CO2 Probe | Removed | Lab none | Removed from Sherman Wetland due to railed readings not responding the atmospheric CO2. |
| TE525MM 65552-615 | 2018-10-18 | Sherman Wetland Precipitation | Calibration | Sherman Wetland Precipitation | Got 94 of 100 tips - adjusted screws a total of 1.5 turns CW
2018-10-18: Got 94 of 100 tips - adjusted screws 0.5 turns CW 2018-10-25: Got 96 of 100 tips - adjusted set screws 1 turn CW. 2018-12-18: 102 tips - no adjustment. |
| TR-525M 50229-112 | 2018-10-18 | East End Precipitation | Calibration | East End Precipitation | Got 94 of 100 tips - adjusted screws a total of 0.5 turns CW.
2018-10-28: Got 98 of 100 tips and adjusted set screws 0.5 turn CW. 2018-11-01: Got 93 of 100 tips - no adjustment and need to retest 2018-12-18: 98 of 100 tips - no adjustment. |
| LI-7700 TG1-0424 | 2018-10-18 | Bouldin Alfalfa Gas Analyzer CH4 | Removed | Lab none | Removed from Bouldin Alfalfa for power board upgrade and to swap in for other two 7700s needing upgrade. |
| LI-7500A 75H-2667 | 2018-10-18 | Lab none | Installed | Bouldin Alfalfa Gas Analyzer CO2/H2O | Installed on Bouldin Alfalfa to replace sn 74H-2150 for calibration. |
| LI-7500A 75H-2150 | 2018-10-18 | Bouldin Alfalfa Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Alfalfa for calibration. Replaced by sn 75H-2667. |
| TE525MM 65560-615 | 2018-10-18 | Bouldin Alfalfa Precipitation | Calibration | Bouldin Alfalfa Precipitation | Got 90 of 100 tips. Adjusted screws a total of 2.5 turns CW.
2018-10-18: Got 90 tips and adjusted screws 1 turn CW. 2018-11-01: Got 91 tips and adjusted screws 2 turns CCW accidentally (should have been CW). 2018-12-13: Got 86 tips and adjusted screws 4.5 turns CW. 2018-12-18: Got 107 tips and adjusted screws 1 turn CCW. |
| LI-7500A 75H-2668 | 2018-10-18 | Lab none | Installed | Bouldin Corn Gas Analyzer CO2/H2O | Installed on Bouldin Corn to replace sn 75H-2182 for calibration |
| LI-7500A 75H-2182 | 2018-10-18 | Bouldin Corn Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Corn for calibration. Replaced by sn 75H-2668. |
| TE525MM 65548-615 | 2018-10-18 | Bouldin Corn Precipitation | Calibration | Bouldin Corn Precipitation | Got 94 of 100 tips. Adjusted a total of 1 turn CW.
2018-10-18: Got 94 of 100 tips - adjusted screws 0.5 turns CW 2018-10-25: Got 97 tips and adjusted set screws 0.5 turn CW. 2018-11-01: 99 of 100 tips - no adjustment. |
| LI-7500A 0418 | 2018-10-17 | Lab none | Installed | Vaira Gas Analyzer CO2/H2O | Installed on Vaira to replace sn 0065 that had no CO2, H2O or signal strength. |
| LI-7500A 0065 | 2018-10-17 | Vaira Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Vaira due to no CO2, H2O or Signal Strength - maybe bad source or detector. Replaced by sn 0418 |
| TR-525I-R1 24875-999 | 2018-10-17 | Vaira Precipitation | Calibration | Vaira Precipitation | Got 78 of 100 tips - adjusted screws 3 turns CW |
| TE525 48132-611 | 2018-10-17 | Tonzi | Calibration | Tonzi | Got 134 of 100 tips - adjusted screws 4 turns CCW |
| TE525 48130-611 | 2018-10-17 | Tonzi | Calibration | Tonzi | Got 88 of 100 tips - adjusted screws 2.5 turns CW |
| TR-525I-R1 24872-999 | 2018-10-17 | Tonzi | Calibration | Tonzi | Got 88 of 100 tips - adjusted screws 2.5 turns CW |
| LI-7500A 75H-2669 | 2018-10-10 | Lab none | Calibration | Lab none | Last calibration: 2018-10-09 AGC=102 SDM=0 DAC1=0 DAC2=0 Ambient P=99.9kPa, Tair=26.6C, Tdew=12.9C Zero Air at 1400psi, AMP Air 408.97 at 1100 Tdewspan=16.00 CO2 zero 0.918 -> .9188 Offset: 3.4ppm CO2 span 1.0125 -> 1.0106 Offset: .9ppm H2O zero 0.8989 -> .8992 Offset: 1.6ppm H2O span 1.0049 -> 1.0034 Offset: .04ppm Notes: Re-calibrated to check Katrina's calibration yesterday, which looks good. |
| LI-7500A 75H-2669 | 2018-10-09 | Lab none | Calibration | Lab none | Last calibration: 2018-06-25 AGC=103 SDM=0 DAC1=0 DAC2=0 Ambient P=99.88kPa, Tair=27.1C, Tdew=12.9C Zero Air at 1425psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.9182 -> .9180 Offset: -.8ppm CO2 span 1.0125 -> 1.0125 Offset: 2.2ppm H2O zero 0.8994 -> .8989 Offset: 52.7ppm H2O span 1.0062 -> 1.0049 Offset: 16.02ppm Notes: Calibrated by Katrina. The H2O offset is large, but the change is coefficients is small, so perhaps Katrina wrote down the wrong offset. |
| LI-7500A 75H-2667 | 2018-10-10 | Lab none | Calibration | Lab none | Last calibration: 2018-10-09 AGC=104 SDM=0 DAC1=0 DAC2=0 Ambient P=99.9kPa, Tair=16.7C, Tdew=11.5C Zero Air at 1400psi, AMP Air 408.97 at 1100 Tdewspan=16.00 CO2 zero 0.9413 -> .9412 Offset: -.5ppm CO2 span 1.0127 -> 1.0145 Offset: -1.57ppm H2O zero 0.8362 -> .8367 Offset: 3.3ppm H2O span 1.0328 -> 1.0218 Offset: .22ppm Notes: Re-calibrated to check Katrina's calibration yesterday, which looks good. |
| LI-7500A 75H-2667 | 2018-10-09 | Lab none | Calibration | Lab none | Last calibration: 2018-06-25 AGC=104 SDM=0 DAC1=0 DAC2=0 Ambient P=99.9kPa, Tair=27.7C, Tdew=9.5C Zero Air at 1450psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.9414 -> .9413 Offset: -.42ppm CO2 span 1.0162 -> 1.0127 Offset: -87.77ppm H2O zero 0.8375 -> .8362 Offset: -7.4ppm H2O span 1.0237 -> 1.0328 Offset: -.19ppm Notes: Calibrated by Katrina. The CO2 span offset is large, but the change is coefficients is small, so perhaps Katrina wrote down the wrong offset. |
| LI-7500A 0418 | 2018-10-10 | Lab none | Calibration | Lab none | Last calibration: 2018-04-13 AGC=93.2 SDM=0 DAC1=0 DAC2=0 Ambient P=99.98kPa, Tair=29.11C, Tdew=15.00C Zero Air at 1500psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.9001 -> .8982 Offset: -7.43ppm CO2 span 1.0057 -> .9965 Offset: 4.86ppm H2O zero 0.8426 -> .8454 Offset: 16.8ppm H2O span 0.9892 -> .9813 Offset: 0.16ppm Notes: calibrated by Katrina |
| LI-7500A 75H-2668 | 2018-10-08 | Lab none | Calibration | Lab none | Last calibration: 2018-10-02 AGC=101 SDM=0 DAC1=0 DAC2=0 Ambient P=99.9kPa, Tair=29.3C, Tdew=5.8C Zero Air at 1500psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.9389 -> .9394 Offset: 2.06ppm CO2 span 1.0172 -> 1.0164 Offset: .38ppm H2O zero 0.9072 -> .9057 Offset: -8.2ppm H2O span 1.0238 -> 1.0157 Offset: .17ppm Notes: Second calibration since chemical swap. Sensor had been running for 5 days, since 10/3 when it had a huge H2O zero offset when analyzing zero gas. I'm not sure why it was reading weird values on 10/3, but the numbers seem ok today, consistent with a chemical swap. In the future, we should let the sensor run for 1 week after swapping internal chemicals, rather than calibrating after only 24 hours. |
| LI-7500A 75H-2180 | 2018-10-04 | Lab none | Installed | Sherman Wetland Gas Analyzer CO2/H2O | Installed on Sherman Wetland to replace sn 75H-2667 for calibration. |
| LI-7500A 75H-2667 | 2018-10-04 | Sherman Wetland Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Sherman Wetland for calibration. Replaced by sn 75H-2180. |
| LI-7500A 0035 | 2018-10-04 | Lab none | Installed | East Pond Gas Analyzer CO2/H2O | Installed on the East Pond tower to replace sn 0418 for calibration. |
| LI-7500A 0418 | 2018-10-04 | East Pond Gas Analyzer CO2/H2O | Removed | Lab none | Removed from the East Pond tower for calibration. Replaced by sn 0035. |
| Mark I A001911 | 2018-10-04 | Lab none | Installed | Bouldin Corn Weather Station A | Installed on Bouldin Corn to replace sn A000251 which is to be sent back to Arable for inspection of backup temperature sensor. Later we realized we had sent back the incorrect Arable; they had requested sn A000591. |
| LI-7500A 1594 | 2018-10-04 | Lab none | Installed | Mayberry Gas Analyzer CO2/H2O | Installed on the Mayberry tower to replace sn 75H-2669 for calibration. |
| LI-7500A 75H-2669 | 2018-10-04 | Mayberry Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Mayberry for calibration. Replaced by sn 1594 |
| LI-7500A 75H-2668 | 2018-10-03 | Lab none | Tested | Lab none | Tested with zero air and the most recent configuration file from 2018-10-02, but CO2 was reading 7.2 umol/mol and H2O was reading -50 mmol/m3. I'm going to let it run a few more days before checking again. |
| LI-7500A 75H-2668 | 2018-10-02 | Lab none | Calibration | Lab none | Last calibration: 2018-09-26 AGC=101 SDM=0 DAC1=0 DAC2=0 Ambient P=99.9kPa, Tair=26.8C, Tdew=15.9C Zero Air at 1600psi, AMP Air 408.97 at 1200 Tdewspan=20.00 CO2 zero 0.9392 -> .9389 Offset: -1.47ppm CO2 span 1.0153 -> 1.0172 Offset: -1.09ppm H2O zero 0.9056 -> .9072 Offset: 9.2ppm H2O span 1.0166 -> 1.0238 Offset: -.16ppm Notes: First calibration after swapping out internal chemicals. Kept the sensor on for 3 days after the swap before the calibration. |
| LI-7500A 1594 | 2018-10-03 | Lab none | Calibration | Lab none | Last calibration: 2018-06-25 AGC=98.6 SDM=0 DAC1=0 DAC2=0 Ambient P=100.16kPa, Tair=28.4C, Tdew=15.18C Zero Air at 1500psi, AMP Air 408.97 at 1200 Tdewspan=20.00 CO2 zero 0.8648 -> .8644 Offset: -1.74ppm CO2 span 1.0181 -> 1.0150 Offset: 1.68ppm H2O zero 0.8869 -> .8870 Offset: 0.8ppm H2O span 1.0106 -> 1.0056 Offset: .11ppm Notes: Spanned H2O at 20.00 because initial dew point temperature in the room was > 16.00 degC. |
| LI-7500A 0035 | 2018-10-02 | Lab none | Calibration | Lab none | Last calibration: 2018-06-25 AGC=98.9 SDM=0 DAC1=0 DAC2=0 Ambient P=99.95kPa, Tair=26.66C, Tdew=16.36C Zero Air at 1550psi, AMP Air 408.96 at 1200 Tdewspan=20.00 CO2 zero 0.9374 -> .9375 Offset: .45ppm CO2 span 1.0296 -> 1.0142 Offset: 1.57ppm H2O zero 0.8979 -> .8981 Offset: 2.3ppm H2O span 1.0261 -> 1.0277 Offset: -.04ppm Notes: Spanned H2O at 20.00 because initial dew point temperature in the room was > 16.00 degC. |
| LI-7500A 75H-2180 | 2018-10-02 | Lab none | Calibration | Lab none | Last calibration: 2018-06-25 AGC=98.6 SDM=0 DAC1=0 DAC2=0 Ambient P=99.86kPa, Tair=27.09C, Tdew=17.03C Zero Air at 1500psi, AMP Air 408.96 at 1200 Tdewspan=20.00 CO2 zero 0.9141 -> .9137 Offset: -1.7ppm CO2 span 1.0267 -> 1.023 Offset: 1.86ppm H2O zero 0.8865 -> .883 Offset: 11.6ppm H2O span 1.0274 -> .9893 Offset: 4.48ppm Notes: Calibrated by Katrina. Spanned H2O at 20.00 because initial dew point temperature in the room was > 16.00 degC. |
| PAR-LITE 010159 | 2018-09-24 | Lab none | Repair | Lab none | Trimmed old cable, soldered on ~10m cable, and secured cable-sensor junction with small L-bracket and zip-ties. |
| LI-7500A 75H-2668 | 2018-09-28 | Lab none | Maintenance | Lab none | Swapped out internal chemicals (Ascarite II and Mg(ClO4)2) because the last three calibrations have H2O zero offsets of +/-10 deg C, which is larger than expected. I flushed the analyzer housing with zero air for a few minutes before replacing the chemical bottles. |
| CR6 2115 | 2018-09-28 | Lab none | Upgrade | Lab none | Upgraded OS from CR6.Std.07.02 to CR6.Std.08.00. After upgrading the OS, I used the "Network Services" tab to enable FTP with the username tower and the usual password. |
| LI-7500A 75H-2514 | 2018-09-27 | Lab none | Installed | Tonzi-Floor | Installed on the Tonzi Tower to replace sn 0035 for calibration. |
| LI-7500A 0035 | 2018-09-27 | Tonzi-Floor Gas Analyzer CO2/H2O | Removed | Lab Gas Analyzer CO2/H2O | Removed from Tonzi Tower for calibration. replaced by sn 75H-2514 |
| LI-7500A 0073 | 2018-09-27 | Lab none | Installed | Tonzi-Tower Gas Analyzer CO2/H2O | Installed on the Tonzi Tower to replace sn 75H-2180 for calibration. |
| LI-7500A 75H-2180 | 2018-09-27 | Tonzi-Tower Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Tonzi Tower for calibration. replaced by sn 0073 |
| LI-7500A 0065 | 2018-09-27 | Lab none | Installed | Vaira Gas Analyzer CO2/H2O | Installed on the Vaira Tower to replace sn 1594 for calibration. |
| LI-7500A 1594 | 2018-09-27 | Vaira Gas Analyzer CO2/H2O | Removed | Lab none | Removed from the Vaira Tower for calibration. Replaced by sn 0065. |
| LI-7500A 0065 | 2018-09-26 | Lab none | Calibration | Lab none | Last calibration: 2018-04-04 AGC=99.7 SDM=0 DAC1=0 DAC2=0 Ambient P=100.4kPa, Tair=26.6C, Tdew=13.8C Zero Air at 1600psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.8905 -> .8903 Offset: -1.09ppm CO2 span 1.0231 -> 1.0184 Offset: 2.48ppm H2O zero 0.7082 -> .7086 Offset: 2.7ppm H2O span 1.0185 -> 1.0155 Offset: .07ppm Notes: |
| LI-7500A 0073 | 2018-09-26 | Lab none | Calibration | Lab none | Last calibration: 2018-04-13 AGC=99.7 SDM=0 DAC1=0 DAC2=0 Ambient P=100.5kPa, Tair=25.8C, Tdew=13.3C Zero Air at 1600psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.9575 -> .9569 Offset: -2.02ppm CO2 span 1.0145 -> 1.0112 Offset: 1.56ppm H2O zero 0.7295 -> .7314 Offset: 2.0ppm H2O span 1.0131 -> 1.0183 Offset: -.12ppm Notes: |
| LI-7500A 75H-2514 | 2018-09-26 | Lab none | Calibration | Lab none | Last calibration: 2018-04-18 AGC=100.1 SDM=0 DAC1=0 DAC2=0 Ambient P=100.3kPa, Tair=27.3C, Tdew=12.7C Zero Air at 1600psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.906 -> .9045 Offset: -6.04ppm CO2 span 1.0106 -> 1.0036 Offset: 3.52ppm H2O zero 0.8368 -> .8370 Offset: 1.3ppm H2O span 1.016 -> 1.0165 Offset: -.01ppm Notes: |
| LI-7500A 75H-2668 | 2018-09-26 | Lab none | Calibration | Lab none | Last calibration: 2018-04-04 AGC=100.0 SDM=0 DAC1=0 DAC2=0 Ambient P=100.4kPa, Tair=26.5C, Tdew=13.8C Zero Air at 1600psi, AMP Air 408.97 at 1200 Tdewspan=16.00 CO2 zero 0.9393 -> 0.9392 Offset: -.27ppm CO2 span 1.0147 -> 1.0153 Offset: -.27ppm H2O zero 0.9038 -> .9056 Offset: 10.6ppm H2O span 1.0146 -> 1.0166 Offset: .05ppm Notes: "Check PLL" error for the first 30 seconds, then status changed to "OK." |
| LAI-2000 PCA-0846 | 2018-09-19 | Lab none | Loaned | Loaned | Loaned to Sebastian Wolf sewolf@ethz.ch for a few weeks for his work a Sagehen. |
| LAI-2000 PCA-1478 | 2018-09-20 | Lab none | Damaged | Lab none | The push button on the wand is failing. |
| GP-001 GP20150109 | 2018-09-18 | Lab none | Installed | East Pond CO2 Probe | Installed at East Pond hanging just below the water surface below the data logger box. |
| CR10X 47253 | 2018-05-23 | Tonzi | Removed | Lab none | Removed from the Tonzi Tower with the old CO2 profile system. New Vaisala profile system is running |
| LI-820 CGA-556 | 2018-05-23 | Tonzi | Removed | Lab none | Removed from the Tonzi Tower with the old CO2 profile system. New Vaisala profile system is running |
| LED-NDVI LED-05 | 2018-05-23 | Tonzi | Removed | Lab none | Removed from the Tonzi Tower because it has not been working for a while and there are Decagon SRS sensors from NDVI and PRI |
| PQS 1 161073 | 2017-08-15 | Factory | Calibration | Factory | y = 209.39*x; Calibrated by Ameriflux at OSU. 4.78 uV/(umol/m2/s). 1000/4.78 = 209.39 (umol/m2/s)/mV |
| AM16-32A 1238 | 2018-07-12 | Loaned | Disposed | Disposed | Given to Tibisay Perez in Whendee Silver's lab in exchange for a new AM16/32B sn 27703 |
| LI-190SA Q29881 | 2007-01-19 | Tonzi PAR Sensor Incoming | Removed | Lab none | Removed from Tonzi Tower top. |
| LI-190SA Q29892 | 2007-01-19 | Tonzi | Removed | Lab none | Removed from Tonzi Tower top. |
| LI-190SA Q29892 | 2001-07-10 | Factory | Calibration | Factory | y = 248.59*x; Initial factory calibration 6.66 uA/(umol/m2/s). Using a 604Ohm millivolt adapter 1000/(6.66*0.604) = 248.59 (umol/m2/s)/mv |
| LI-190SA Q29892 | 2001-09-07 | Lab none | Installed | Tonzi | Installed on the Tower top in the outgoing position |
| LI-190SA Q29881 | 2001-09-07 | Lab none | Installed | Tonzi PAR Sensor Incoming | Installed on the Tower top in the incoming position |
| LI-190SA Q29881 | 2001-07-10 | Factory | Calibration | Factory | y = 248.97*x; Initial factory calibration 6.65 uA/(umol/m2/s). Using a 604Ohm millivolt adapter 1000/(6.65*0.604) = 248.97 (umol/m2/s)/mv |
| CNR1 990181 | 2001-05-20 | Lab none | Installed | Vaira Net Radiometer 4-way | Installed on the Vaira tower |
| NR-LITE 990351 | 2001-05-20 | Lab none | Installed | Tonzi | Installed on the Tower top with the initial set up of the site |
| PAR-LITE 990017 | 2001-05-20 | Lab none | Installed | Tonzi | Installed on the Tower top in the reflected PAR location with the initial set up of the site |
| PAR-LITE 990019 | 2001-05-20 | Lab none | Installed | Tonzi | Installed on the Tower Top in the incoming PAR position. |
| PAR-LITE 990021 | 2001-05-20 | Lab none | Installed | Tonzi | Installed on the Tower top as a calibration sensor |
| eosFD 20160002 | 2012-10-17 | Lab none | Troubleshooting | Lab none | This chamber was installed at the Tonzi soil co2 profile at the Open location but did not start up. I brought it back in to test. Eosense mentioned a “heat-start-up issue†but thought it had been fixed. It tested fine in the lab. |
| HMP45AC T2130005 | 2018-08-23 | Lab none | Installed | Sherman Wetland RH & Temp | Installed at SW to replace the other HMP45 with a too short cable. Mounted in the original location. 1% slope in T and 6% slope in RH from TA inter-comparison. |
| HMP45AC W0730036 | 2018-08-23 | Sherman Wetland RH & Temp | Removed | Lab none | Removed from SW because its cable was to short to allow it to be mounted in the correct place. |
| HMP45AC T1250012 | 2018-08-23 | Lab none | Installed | Bouldin Alfalfa RH & Temp | Installed on BA to replace an HMP60 with low temperature readings. This sensor was in the TA inter-comparison T slope was 1.0462 and RH slope was 1.0369. |
| HMP60 L1740398 | 2018-08-23 | Bouldin Alfalfa RH & Temp | Removed | Lab none | Removed from BA due to low temperature readings. Several other HMP60s have similarly failed. |
| eosFD FD20160001 | 2018-08-07 | Lab none | Installed | Bouldin Alfalfa Forced Diffusion A | Installed under the BA scaffolding over bare soil. |
| HMP45AC W0730036 | 2018-08-07 | Lab none | Installed | Sherman Wetland RH & Temp | Installed at SW to replace HMP60 sn L2310736. The HMP60 was reading numbers lower than reasonable. |
| HMP60 L2310736 | 2018-08-07 | Sherman Wetland RH & Temp | Removed | Lab none | Removed from SW because it has been reading too low. It was replaced with HMP45 sn W0730036. |
| Raven XT 1131631861 | 2012-01-09 | Lab none | Installed | Tonzi | Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| NR01 1514 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -8cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| HFP01SC 2500 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at about 1m agl at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| HFP01SC 2495 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -8cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| SX350J T21009229B37030 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| RF401 35785 | 2012-01-09 | Lab none | Installed | Tonzi | Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| SX229 15731 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -60cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| SX229 15729 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -20cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| SX229 15802 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -10cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| SX229 15852 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -5cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| SX229 15730 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -40cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| SX229 15764 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -80cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| STD-5TE 5TE-1400 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -80cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| STD-5TE 5TE-1274 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -60cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| STD-5TE 5TE-1275 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -40cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| STD-5TE 5TE-1393 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -20cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| STD-5TE 5TE-1281 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -5cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| STD-5TE 5TE-1287 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -10cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |
| STD-5TE 5TE-1278 | 2012-01-09 | Lab none | Installed | Tonzi | Installed at -2cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. |