Equipment and Calibration History
Page: 1 2 3 4 5 6 7 [8] 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71| Ser No. | Date | Loc From | Title | Loc To | Notes |
|---|---|---|---|---|---|
| GMP343 N2220008 | 2024-02-27 | Lab none | Installed | Tonzi CO2 Probe Tower Profile 23 | Reinstalled in the top location of the Tower co2 profile after testing in the lab. Reinstalled cable. |
| GMP343 N2210009 | 2024-02-27 | Lab none | Installed | Tonzi CO2 Probe Tower Profile 6 | Reinstalled in the upper-mid location of the Tower co2 profile after testing in the lab. |
| GMP343 N2210010 | 2024-02-27 | Lab none | Installed | Tonzi CO2 Probe Tower Profile 1.8 | Reinstalled in the lower-mid location of the Tower co2 profile after testing in the lab. |
| GMP343 N2220007 | 2024-02-27 | Lab none | Installed | Tonzi CO2 Probe Tower Profile 0.35 | Reinstalled in the bottom location of the Tower co2 profile after testing in the lab. New cable. |
| SONIC-ANEMO-SPE10 022365410 | 2024-02-14 | Lab none | Installed | Bouldin Corn none | Installed at Bouldin Corn with a new, udpated Mark 3, sn D006617. |
| Mark 3 D006617 | 2024-02-14 | Lab none | Installed | Bouldin Corn none | Installed at Bouldin Corn with a new 2-D sonic, sn 022365410, to replace the older Mark 3, sn B301069. |
| Mark 3 B301069 | 2024-02-14 | Bouldin Corn | Removed | Lab none | Removed from Bouldin Corn and replaced with the updated Mark 3 sn D006617. This older Mark 3 will be sent back to Loreli. |
| A547 3586 | 2024-02-12 | West Pond Interface A547 | Removed | Lab none | Removed from WP with conductivity sensor sn 6096 and brought back to the lab. Nothing wrong with the data (probably), I just wanted an extra sensor in the lab to play around with TempCoef. |
| LI-7700 TG1-0424 | 2024-02-26 | Lab | Calibration | Lab | Calibration Location: Lab Last calibration: 2023-09-05 RSSI=77%, Optical RH=5% Ambient P=100.6kPa, Tair=23.0C Zero Air at 350psi, AMP CA04119 4.223 at 600 CH4 Zero Offset: -.063ppm CH4 Span Offset: .009ppm Notes: BWW sensor. After installing it again, I put the spiky hat and spray nozzle on again. The was reservoir was empty; Haley refilled it. |
| LI-7500A 75H-2150 | 2024-02-26 | Lab | Calibration | Lab | Last calibration: 2023-11-09 AGC=102.8 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.4kPa, Tair=24.1C, Tdew=10.96C Zero Air at 350psi, AMP CA04119 575 at 524.77 Tdewspan=20.00 CO2 zero 0.9041 -> .9030 Offset: -5.59ppm CO2 span 1.018 -> 1.0175 Offset: .48ppm H2O zero 0.8731 -> .8737 Offset: 3.5ppm H2O span 1.0265 -> 1.0382 Offset: -.25ppm Notes: BWW tower sensor. One of the mount screws wouldn't come out initially; Joe got it out pulsing with vice grips + WD-40. He cleaned out the white dust inside the bolt holes with a thread cutter. He sprayed the bolts and bolt holes with a anti-corrosion spray before I installed it again. The 7550 temperature sensor was bad. I replaced with a repaired homemade temperature sensor. The HMP fan was not spinning, but it seemed to work fine after I removed a bit of fluff. |
| SONIC-ANEMO-SPE10 022365394 | 2024-02-14 | Lab none | Installed | Bouldin Alfalfa Weather Station B | Added to the new Arable Mark 3 sn D006812 |
| Mark 3 D006812 | 2024-02-14 | Lab none | Installed | Bouldin Alfalfa Weather Station B | Installed at Bouldin Alfalfa to replace sn B301045 |
| Mark 3 B301045 | 2024-02-14 | Bouldin Alfalfa Weather Station B | Removed | Lab none | Removed from Bouldin Alfalfa. Replaced by sn D006812. |
| LI-7700 TG1-0421 | 2024-02-16 | Lab | Calibration | Lab | Calibration Location: Lab Last calibration: 2023-02-02 RSSI=81%, Optical RH=12% Ambient P=100.98kPa, Tair=21.5C Zero Air at 450psi, AMP CA04119 4.2238 at 675 CH4 Zero Offset: .032ppm CH4 Span Offset: .0058ppm Notes: Calibration before loaning this sensor to J.J. to use at Elkhorn Slough Yampah tower while they're waiting for replacement/repair |
| LI-7700 TG1-0421 | 2024-02-16 | Lab none | Loaned | Loaned none | Loaned sensor to Sylvain and J.J. (UCSC) to use at the Elkhorn Slough Yampah tower while they wait for a replacement sensor/repairs. Spiky hat was not loaned. Cables were loaned: 7700 yellow power cable, 7700 green Ethernet cable, wash black power cable, wash black tubing without spray nozzle (spray nozzle loaned previously for UCSC to use at Elkhorn Porter tower) |
| HMP155 T2930114 | 2024-02-16 | Lab none | Loaned | Loaned none | Loaned sensor and cable to Sylvain and J.J. (UCSC) to use at the Elkhorn Slough Yampah tower while they wait for a replacement sensor/repairs. |
| CS547A 6096 | 2024-02-12 | West Pond Conductivity Sensor | Removed | Lab none | Removed from WP with interface sn 3586 and brought back to the lab. Nothing wrong with the data (probably), I just wanted an extra sensor in the lab to play around with TempCoef. |
| LI-7500A 0418 | 2024-02-12 | Lab none | Installed | Gilbert Tract Gas Analyzer CO2/H2O | Installed at Gilbert Tract to replace sn 75H-2176 for calibration. |
| LI-7500A 75H-2176 | 2024-02-12 | Gilbert Tract Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Gilbert Tract for calibration. Replaced by sn 0418. |
| LI-7500A 0418 | 2024-02-09 | Lab | Calibration | Lab | Last calibration: 2023-10-23 AGC=101.3 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.68kPa, Tair=23.2C, Tdew=5.6C Zero Air at 475psi, AMP CA04119 524.77 at 700 Tdewspan=20.00 CO2 zero 0.9072 -> .9075 Offset: 1.41ppm CO2 span 1.0066 -> 1.0063 Offset: .14ppm H2O zero 0.9331 -> .9317 Offset: -7.5ppm H2O span 1.0052 -> 1.002 Offset: .08ppm Notes: Vertical orientation. H2O zero only took 10min to stabilize |
| CS547A 6097 | 2024-02-13 | Disposed none | Notes | Disposed none | Found this sensor in the dead sensor box in the lab! We were able to find the Kc (cell constant) on its label. This was not previously recorded in the equipment entry, and Campbell did not have any record of it either. Incontrovertible proof that we should never throw anything away. |
| GMP343 N2210009 | 2024-02-09 | Tonzi CO2 Probe Tower Profile 6 | Removed | Lab none | Removed from the upper mid location on the Tower due to bad readings and to be calibrated |
| GMP343 N2210010 | 2024-02-09 | Tonzi CO2 Probe Tower Profile 1.8 | Removed | Lab none | Removed from the lower mid location on the Tower due to bad readings and to be calibrated |
| GMP343 N2220007 | 2024-02-09 | Tonzi CO2 Probe Tower Profile 0.35 | Removed | Lab none | Removed from the lowest location on the Tower due to bad readings, cow chewed cable and to be calibrated |
| CS655 17131 | 2024-01-30 | Lab none | Installed | Mayberry none | Installed at MB in a tule patch southeast of the tower (~50cm from the staff gauge). This is a test to see if we can continuously track porewater salinity changes. |
| CS655 17130 | 2024-01-30 | Lab none | Installed | Mayberry none | Installed at MB in the channel in front of the tower. This is a test to see if we can continuously track porewater salinity changes. |
| HMP155 T2820180 | 2024-01-25 | Factory none | Disposed | Disposed none | Campbell's evaluation: Inspected. Cap filter is dirty and sticker labels started to peel off suggesting sensor has been deployed in a very humid environment. After tests sensor showed problems to provide correct RH and Temp data. Unfortunately sensor can't be repaired or calibrated. Warranty expired o 08-27-2022. NOTE: We suggest to acquire a new unit such as the HygroVUE10, which offers advantages worth look up, as a replacement for the damaged one. Dead unit will be returned so that I can take it apart! |
| HMP155 T2820180 | 2024-01-17 | Lab none | Shipped | Factory none | Sent to Campbell on RMA 37957. RH and AirT are reading zero. |
| EXO2 22C103416 | 2024-01-23 | Lab none | Tested | Lab none | The wiper sn 22E103340 hasn't worked properly since being installed in mid-December. When we pulled the sonde last week, the brush was parked over the pH sensor and all the sensors were dirty. I brought the sonde back to the lab for routine calibration and tested the brush. The brush did work smoothly as first, but then it became intermittent. Sometimes it didn't work at all and sometimes it worked only in spurts (and the EXO would disconnect from the laptop right before the brush moved). The wiper did not show up under the Sensors or Calibration tab. Nothing changed when I tried plugging the wiper into a different port. I talked to Matt at YSI who thinks something is messed up electronically inside the wiper--it can receive commands (to wipe) but is not talking back to the sonde. I will send the wiper back to YSI for repair. |
| EXO2 22C103416 | 2022-09-29 | Lab none | Calibration | Lab none | Depth (m), Last cal: 9/23/2022 11:38:38 AM
EXO sn 22C103416 EXO/Sensor Firmware: 1.0.86/3.1.3 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.000 m,0.109 m,0.000 m,0.000 m,22.000 °C |
| EXO2 22C103416 | 2024-01-22 | Lab none | Calibration | Lab none | Depth(m),Last cal: 2023-10-18 EXO sn 22C103416 EXO/Sensor Firmware 1.0.86/3.1.3 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.000 m,-0.076 m,0.000 m, 0.000 m, 17.888 °C |
| EXO pH-ORP 22D102641 | 2024-01-22 | Lab none | Calibration | Lab none | pH, Last cal: 2023-10-16
EXO sn 22C103416 EXO/Sensor Firmware: 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,7.01 pH,7.01 pH,7.01 pH,-4.8 mV,19.428 °C Pt2,10.06 pH,10.04 pH,10.06 pH,-174.7 mV,20.116 °C Pt3,4.00 pH,4.05 pH,4.01 pH,161.2 mV,21.033 °C 4-7Slope,4-7mVPerDecade,7-10Slope,7-10mVPerDecade 166.0 mV,55.16,169.9 mV,55.71 Note: Calibration pretty close and delta slope and mV per decade are ok. Used opened standards from May 2023. |
| EXO pH-ORP 22D102641 | 2024-01-22 | Lab none | Calibration | Lab none | ORP (mV), Last Cal: 2023-10-16 EXO sn 22C103416 EXO/Sensor Firmware 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,230.4 mV,227.6 mV,223.3 mV,0.0 mV,21.275 °C Note: Poured Zobell solution (mixed 2022-09) into small brown plastic bottle for this calibration. |
| EXO Wiped Cond/Temp 23D104030 | 2024-01-22 | Lab none | Calibration | Lab none | Sp Cond (uS/cm),Last cal: 2023-08-17 EXO sn 22C103416 EXO/Sensor Firmware 1.0.86/3.0.5 CellConstant 0.46 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,8420.0 µS/cm,8507.6 µS/cm,8420.0 µS/cm, 0.0 µS/cm,20.226 °C Note: Used 10,000 uS/cm standard from fridge (brought it to room temperature first). Measured temp-compensated conductivity with handheld YSI probe |
| EXO Turbidity 22E106072 | 2024-01-22 | Lab none | Calibration | Lab none | Turbidity (FNU), Last cal: 2023-10-16
EXO sn 22C103416 EXO/Sensor Firmware: 1.0.86/3.0.4 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 FNU,3.85 FNU,0.00 FNU,0.00 FNU,21.571 °C Pt2,124.00 FNU,122.47 FNU,124.00 FNU,0.00 FNU,20.745 °C Pt3,1010.00 FNU, 959.99 FNU, 1010.00 FNU, 0.00 FNU, 20.651 °C Note: Used the lab's DI water for zero point for this and previous calibrations. I'll try to get some miliQ water for future calibrations since this zero point had a larger than usual offset. Probably doesn't affect our data too much since our turbidity is usually >50 FNU. |
| EXO fDOM 22E100649 | 2024-01-23 | Lab none | Calibration | Lab none | fDOM (QSU and RFU), Last cal: 2023-08-17 EXO sn 22C103416 EXO/Sensor Firmware: 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 QSU,-2.68 QSU,0.00 QSU,0.00 QSU,20.692 °C Pt2,300.00 QSU,182.33 QSU,300.08 QSU,0.00 QSU,21,776 °C Notes: Fresh calibration solution after a factory reset. Previous calibration attempts in the last few days were all really off. Keep an eye on this sensor. ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 RFU,0.24 RFU,0.00 RFU,0.00 RFU,20.081 °C Pt2,100.0 RFU,RFU,122.16 RFU,100.05 RFU,0.00 RFU,22.019 °C Notes: Fresh calibration solution after a factory reset |
| EXO pH-ORP 22D102641 | 2024-01-18 | Hill Slough pH-ORP | Removed | Lab none | Removed from HS channel and brought back to the lab for routine calibration |
| EXO Wiped Cond/Temp 23D104030 | 2024-01-18 | Hill Slough Conductivity Sensor | Removed | Lab none | Removed from HS channel and brought back to the lab for routine calibration |
| EXO fDOM 22E100649 | 2024-01-18 | Hill Slough fDOM | Removed | Lab none | Removed from HS channel and brought back to the lab for routine calibration |
| EXO Turbidity 22E106072 | 2024-01-18 | Hill Slough Turbidity | Removed | Lab none | Removed from HS channel and brought back to the lab for routine calibration |
| EXO2 22C103416 | 2024-01-18 | Hill Slough Water Level | Removed | Lab none | Removed from HS channel and brought back to the lab for routine calibration |
| LI-7500A 75H-2418 | 2024-01-23 | Lab none | Returned | Returned none | Returned to Stephen Chan at LBL. Returned with AMP LI-7550 sn AIU-1039, a 7550 thermistor, IRGA cable, and IRGA mount. |
| LI-7550 AIU-1039 | 2024-01-23 | Lab none | Returned | Returned none | Returned to Stephen Chan at LBL now that our 7550 AIU-1866 is back from the factory. AMP 7550 Returned with AMP LI-7500A sn 75H-2418, a 7550 thermistor, IRGA cable, and IRGA mount. |
| LI-7500A 1594 | 2024-01-18 | Lab none | Installed | Hill Slough Gas Analyzer CO2/H2O | Installed at Hill Slough to replace sn 0418 for calibration. |
| LI-7500A 0418 | 2024-01-18 | Hill Slough Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Hill Slough for calibration. Replaced by sn 1594. |
| LI-7500A 75H-2182 | 2024-01-18 | Lab none | Installed | East End Gas Analyzer CO2/H2O | Installed at East End to replace sn 75H-2180 for calibration. |
| LI-7500A 75H-2180 | 2024-01-18 | East End Gas Analyzer CO2/H2O | Removed | Lab none | Removed from East End for calibration. Replaced by sn 75H-2182. |
| miniDOT-usb 180871 | 2024-01-18 | Lab none | Installed | Gilbert Tract DO Sensor Channel | Installed on the back of the ADCP mount to measure the channel's DO. Channel DO was previously measured with miniDOT sn 1221 co-located with the USGS EXO, but that miniDOT stopped working last August. |
| miniDOT-usb 180871 | 2024-01-11 | West Pond DO Sensor A | Removed | Lab none | Removed from WP with site decommissioning |
| PAR-LITE 010161 | 2024-01-11 | Mayberry PAR Sensor Reflected Water | Removed | Lab none | Removed from MB tower because it was no longer measuring open water (wetland is filling in with cattails) |
| NR-LITE 990351 | 2024-01-11 | Mayberry Net Radiometer Water | Removed | Lab none | Removed from MB tower because it was no longer measuring open water (wetland is filling in with cattails) |
| LI-7700 TG1-0421 | 2024-01-11 | Hill Slough Gas Analyzer CH4 | Removed | Lab none | Removed from HS and brought back to the lab for calibration. It was replaced by sn TG1-0155 |
| LI-7700 TG1-0155 | 2024-01-11 | Lab none | Installed | Hill Slough Gas Analyzer CH4 | Installed at HS to replace sn TG1-0421, which was removed for calibration |
| LI-7700 TG1-0423 | 2024-01-11 | East End | Calibration | East End | Calibration Location: East End Last calibration: 2023-06-15 RSSI=79%, Optical RH=23% Ambient P=102.2kPa, Tair=16.0C Zero Air at 1800psi, AMP CA03923 3.3865 at 1725 CH4 Zero Offset: .015ppm CH4 Span Offset: .0015ppm Notes: After calibration, flushed headspace with zero air until optics RH=9% and swapped in a bottle with fresh drierite. |
| LI-7700 TG1-0223 | 2024-01-11 | Gilbert Tract | Calibration | Gilbert Tract | Calibration Location: Gilbert Tract Last calibration: 2023-08-07 RSSI=82%, Optical RH=3% Ambient P=101.8kPa, Tair=9.7C Zero Air at 1850psi, AMP CA03923 3.3865 at 1750 CH4 Zero Offset: .002ppm CH4 Span Offset: -.0225ppm Notes: Breezy |
| LI-7700 TG1-0357 | 2024-01-11 | Bouldin Corn | Calibration | Bouldin Corn | Calibration Location: Bouldin Corn Last calibration: 2023-06-14 RSSI=71%, Optical RH=9% Ambient P=102.0kPa, Tair=13.3C Zero Air at 1700psi, AMP CA03923 3.3865 at 1700 CH4 Zero Offset: .035ppm CH4 Span Offset: -.0215ppm Notes: Still day for once |
| LI-7700 TG1-0211 | 2024-01-11 | Mayberry | Calibration | Mayberry | Calibration Location: Mayberry Last calibration: 2023-07-20 RSSI=71%, Optical RH=3% Ambient P=102.1kPa, Tair=11.5C Zero Air at 1850psi, AMP CA03923 3.3865 at 1700 CH4 Zero Offset: .032ppm CH4 Span Offset: .0095ppm Notes: Breezy day |
| LI-7500A 75H-2182 | 2024-01-10 | Lab | Calibration | Lab | Last calibration: 2023-10-23 AGC=103 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.21kPa, Tair=21.2C, Tdew=9.47C Zero Air at 450psi, AMP CA04119 524.77 at 650 Tdewspan=18.00 CO2 zero 0.8848 -> .885 Offset: .94ppm CO2 span 1.0124 -> 1.0163 Offset: -2.06ppm H2O zero 0.8311 -> .8326 Offset: 9.9ppm H2O span 1.0325 -> 1.0352 Offset: -.05ppm Notes: Vertical orientation. Reset SS from 103 to 100 after cal. Used nail polish to cover up some small patches of paint missing from the spars. |
| LI-7500A 1594 | 2024-01-10 | Lab | Calibration | Lab | Last calibration: 2023-10-03 AGC=103 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.22kPa, Tair=21.03C, Tdew=9.42C Zero Air at 450psi, AMP CA04119 524.77 at 675 Tdewspan=18.00 CO2 zero 0.8777 -> .8774 Offset: -1.37ppm CO2 span 1.0092 -> 1.0093 Offset: -.7ppm H2O zero 0.8117 -> .8142 Offset: 14.7ppm H2O span 1.0074 -> 1.0062 Offset: .03ppm Notes: Vertical orientation. Reset SS from 103 to 100 after cal. |
| LI-7700 TG1-0155 | 2024-01-10 | Lab | Calibration | Lab | Calibration Location: Lab Last calibration: 2023-06-15 RSSI=91%, Optical RH=21% Ambient P=100.46kPa, Tair=21.3C Zero Air at 500psi, AMP CA04119 4.2238 at 750 CH4 Zero Offset: -.03ppm CH4 Span Offset: -.0188ppm Notes: This sensor was removed from WP with its decommissioning. Back in the lab, it had revert to default heater settings and its clock was off (laptop=11:46, 7700=18:51, "Etc/GMT+8" on slave). I changed the clock setting to automatic, set the clock to match the laptop time, changed the clock setting back to slave, and then rebooted. The time was correct after reboot but we should double-check it after conencting to the 7550 in the field. I changed the heater settings back to our usual. Before calibration, I flushed the optics headspace down to 10% and swapped in a bottle of fresh drierite. |
| LI-7500A 0041 | 2024-01-04 | Lab none | Installed | Mayberry Gas Analyzer CO2/H2O | Installed at Mayberry to replace sn 0073 for calibration. |
| LI-7500A 0073 | 2024-01-04 | Mayberry Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Mayberry for calibration. Replaced by sn 0041. |
| LI-7500A 1594 | 2024-01-04 | West Pond Gas Analyzer CO2/H2O | Removed | Lab none | Removed from WP tower with initial decommissioning of the site |
| LI-7700 TG1-0155 | 2024-01-04 | West Pond Gas Analyzer CH4 | Removed | Lab none | Removed from WP tower with initial decommissioning of the site |
| LI-7500A 75H-2180 | 2024-01-04 | Lab none | Installed | East End Gas Analyzer CO2/H2O | Installed at East End to replace sn 75H-2182 for calibration. |
| LI-7500A 75H-2182 | 2024-01-04 | East End Gas Analyzer CO2/H2O | Removed | Lab none | Removed from East End for calibration. Replaced by sn 75H-2180. |
| SI-131 1076 | 2024-01-04 | Bouldin Corn Infrared Temperature South | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| SI-131 1073 | 2024-01-04 | Bouldin Corn Infrared Temperature North | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| CH150 2963 | 2024-01-04 | Bouldin Corn Solar Controller Surface Renewal | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| CR1000X 1132 | 2024-01-04 | Bouldin Corn Data Logger Surface Renewal | Removed | Lab none | Removed from BC at the conclusion of Corteva's IRT experiment. |
| LI-7500A 0065 | 2024-01-04 | Lab none | Installed | Bouldin Corn Gas Analyzer CO2/H2O | Installed at Bouldin Corn to replace sn 0042 for calibration. |
| LI-7500A 0042 | 2024-01-04 | Bouldin Corn Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Corn for calibration. Replaced by sn 0065. |
| SI-121 1635 | 2024-01-04 | Bouldin Alfalfa Infrared Temperature South | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| SI-131 1071 | 2024-01-04 | Bouldin Alfalfa Infrared Temperature North | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| CH150 1688 | 2024-01-04 | Bouldin Alfalfa Solar Controller Surface Renewal | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| CR1000X 1130 | 2024-01-04 | Bouldin Alfalfa Data Logger Surface Renewal | Removed | Lab none | Removed from BA tower at the conclusion of Corteva's IRT experiment. |
| LI-7500A 0035 | 2024-01-02 | Lab none | Installed | Vaira Gas Analyzer CO2/H2O | Installed at Vaira to replace sn 0065 for calibration |
| LI-7500A 0065 | 2024-01-02 | Vaira Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Vaira for calibration. Replaced by sn 0035. |
| PRB-K Type #8 00000A3D04E8 | 2024-01-02 | Tonzi none | Removed | Lab none | This probes has been broken for a long time - more than a year. Removed. It has a broken pin and the shaft is cracked. |
| LI-7500A 75H-2669 | 2024-01-02 | Lab none | Installed | Tonzi-Tower Gas Analyzer CO2/H2O | Installed at Tonzi Tower to replace sn 75H-2180 for calibration. |
| LI-7500A 75H-2180 | 2024-01-02 | Tonzi-Tower Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Tonzi-Tower for calibration. Replaced by sn 75H-2669. |
| LI-7500A 75H-2667 | 2024-01-02 | Lab none | Installed | Tonzi Gas Analyzer CO2/H2O Floor | Installed at Tonzi Floor to replace sn 0041 for calibration. |
| LI-7500A 0041 | 2024-01-02 | Tonzi Gas Analyzer CO2/H2O Floor | Removed | Lab none | Removed from Tonzi Floor for calibration. Replaced by sn 75H-2667. |
| LI-7500A 0065 | 2024-01-03 | Lab | Calibration | Lab | Last calibration: 2023-09-18 AGC=100 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=22.7C, Tdew=7.3C Zero Air at 550psi, AMP CA04119 524.77 at 700 Tdewspan=20.0 CO2 zero 0.8919 -> 0.8918 Offset: -0.27ppm CO2 span 1.024 -> 1.0255 Offset: -1.3ppm H2O zero 0.7322 -> 0.7329 Offset: 4.9ppm H2O span 1.0226 -> 1.0238 Offset: -0.02ppm Notes: Signal strength rest from 107 to 100 before calibration. Used CO2 span pt of 524.67 |
| LI-7500A 0041 | 2024-01-03 | Lab | Calibration | Lab | Last calibration: 2023-09-18 AGC=100 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=22.7C, Tdew=7.3C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=20.0 CO2 zero 0.9965 -> 0.9963 Offset: -0.79ppm CO2 span 1.0192 -> 1.0217 Offset: -1.67ppm H2O zero 0.8236 -> 0.8245 Offset: 5.0ppm H2O span 1.0292 -> 1.0365 Offset: -0.16ppm Notes: H20 took a long time (40min) to stabilize - kept creeping up |
| LI-7500A 75H-2180 | 2024-01-03 | Lab | Calibration | Lab | Last calibration: 2023-09-18 AGC=101.1 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=23.1C, Tdew=7.9C Zero Air at 500psi, AMP CA04119 524.77 at 700 Tdewspan=20.0 CO2 zero 0.9143 -> 0.9141 Offset: -0.8ppm CO2 span 1.0384 -> 1.0406 Offset: -1.17ppm H2O zero 0.8944 -> 0.8965 Offset: 12.9ppm H2O span 1.0344 -> 1.0383 Offset: -0.08ppm Notes: |
| LI-7500A 0035 | 2024-01-02 | Lab | Calibration | Lab | Last calibration: 2023-08-04 AGC=100.5 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=101.0kPa, Tair=19.96C, Tdew=8.97C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9377 -> 0.9372 Offset: -2.0ppm CO2 span 1.024 -> 1.0267 Offset: -1.77ppm H2O zero 0.8984 -> 0.9006 Offset: 13.4ppm H2O span 1.0205 -> 1.0400 Offset: -0.4ppm Notes: I painted some scratches on the body with nail polish |
| HYDROS21 H21G200002433 | 2023-12-22 | Lab none | Installed | Hill Slough Water Level | Installed at the channel to replace the one that failed and was removed a while ago. |
| LI-7500A 75H-2514 | 2023-12-22 | Lab none | Installed | Bouldin Alfalfa Gas Analyzer CO2/H2O | Installed at Bouldin Alfalfa to replace sn 0035 for calibration. |
| LI-7500A 0035 | 2023-12-22 | Bouldin Alfalfa Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Alfalfa for calibration. Replaced by sn 75H-2514. |
| HMP45AC D4420028 | 2023-12-22 | Lab none | Installed | Mayberry RH & Temp | Installed at MB to replace HMP155 that died and was removed last visit. HMP155 cable removed this time. Met program updated for different AirT offset. |
| LI-7500A 75H-2669 | 2023-12-20 | Lab | Calibration | Lab | Last calibration: 2023-08-04 AGC=100.0 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=99.6kPa, Tair=22.4C, Tdew=15.48C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9195 -> 0.9187 Offset: -3.0ppm CO2 span 1.0167 -> 1.0167 Offset: -0.02ppm H2O zero 0.9009 -> 0.9027 Offset: 10.9ppm H2O span 1.0163 -> 1.0206 Offset: -0.09ppm Notes: Reset SS from 102.6 |
| LI-7500A 75H-2667 | 2023-12-20 | Lab | Calibration | Lab | Last calibration: 2023-07-10 AGC=100.0 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=99.6kPa, Tair=21.7C, Tdew=10.4C Zero Air at 500psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9411 -> 0.9413 Offset: 0.7ppm CO2 span 1.0232 -> 1.0207 Offset: 1.83ppm H2O zero 0.8427 -> 0.8427 Offset: 0.2ppm H2O span 1.0367 -> 1.0363 Offset: 0.01ppm Notes: Reset SS from 103.0, Database says last cal was 07-14, instrument says 07-10. |
| LI-7500A 75H-2514 | 2023-12-20 | Lab | Calibration | Lab | Last calibration: 2023-07-10 AGC=100.0 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=99.6kPa, Tair=20.4C, Tdew=11.0C Zero Air at 600psi, AMP CA04119 524.77 at 750 Tdewspan=18.0 CO2 zero 0.9049 -> 0.9095 Offset: -3.4ppm CO2 span 1.0199 -> 1.0207 Offset: -0.37ppm H2O zero 0.8426 -> 0.8461 Offset: 3.5ppm H2O span 1.0244 -> 0.9962 Offset: -0.03ppm Notes: Calibration after factory repair and calibration. Reset SS from 103.4. Added SD coefficients to configuration. |
| eosFD FD20200001 | 2023-12-13 | Vaira Forced Diffusion North | Moved | Tonzi-SoilCO2 Forced Diffusion Tree 1 | Moved from Vaira North location to the Tonzi Tree 1 location. waiting for one FD to be repaired by Eosense. |
| PA-II-SD 68c63acc07a9 | 2023-12-07 | Lab none | Installed | Bouldin Corn Air Quality Sensor | Installed on the BC tower in its usual spot on the southwest corner. This PA has a new card slot that Joe put in. I had brought the sensor home last week so that it could reset its clock on my wifi. However, now campus has an IOT wifi network, so maybe I can try connecting the PA to it next time. |
| HYDROS21 H21G200002263 | 2023-12-08 | Lab none | Installed | Mayberry Water Level | Installed on the northeastern corner of the Mayberry scaffolding. There's not much water right now, but I tried to install it right above the muck. |
| HMP155 T2820180 | 2023-12-08 | Mayberry RH & Temp | Removed | Lab none | Removed from the Mayberry tower and brought back to the lab for testing. It was reading -79 deg C and 0% RH. |
| HMP45AC D4420028 | 2023-12-13 | Lab none | Tested | Lab none | Plugged in for a few minutes in a lab and still compares fine with the cal kit HMP155. We will use this sensor Mayberry to replace the dead HMP155 sn T2820180. |
| LI-7500A 75H-2514 | 2023-11-13 | Factory none | Calibration | Factory none | Calibrated at Licor after chopper motor replacement - see RMA doc: rma_Licor_00248550_sn75H-2514_20231201.pdf. The new calibration numbers (see cal doc: cal_Licor_LI-7500A_sn75H-2514_20231113.pdf) will need to be manually entered in 7550 configuration file. |