Equipment and Calibration History
Page: 1 [2] 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70| Ser No. | Date | Loc From | Title | Loc To | Notes |
|---|---|---|---|---|---|
| LI-7500A 0065 | 2025-01-09 | Tonzi Gas Analyzer CO2/H2O Floor | Removed | Lab none | Removed from Tonzi Floor for calibration. Replaced by sn 0042. |
| LI-7500A 0035 | 2025-01-09 | Lab none | Installed | Vaira Gas Analyzer CO2/H2O | Installed at Vaira to replace sn 75H-2180 for calibration. |
| LI-7500A 75H-2180 | 2025-01-09 | Vaira Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Vaira for calibration. Replaced by sn 0035. |
| LI-7500A 75H-2667 | 2025-01-07 | Lab none | Calibration | Lab none | Last calibration: 2024-07-19
AGC=98.8 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=101.0kPa, Tair=25.9C, Tdew=2.99C Zero Air at 900psi, AMP FB04319 514.07 at 400 Tdewspan=20.00 CO2 zero 0.9416 -> .9410 Offset: -2.32ppm CO2 span 1.0177 -> 1.0165 Offset: .64ppm H2O zero 0.8407 -> .8454 Offset: 29.2ppm H2O span 1.0371 -> 1.0393 Offset: -.04ppm Notes: Larger H2O zero offset (29.2 mmol/m3) than usual, but it was offset by the offset from the previous calibration (-20.2 mmol/m3). There is a consistent drift in the H2O zero coefficient since 2023. I don't think the chemicals have been swapped since 2016, so I could do that next time. Used "514.03" as CO2 span point in the 7550 software. |
| LI-7500A 0042 | 2025-01-07 | Lab | Calibration | Lab | Last calibration: 2024-07-12 AGC=101.8 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.9kPa, Tair=26.2C, Tdew=2.35C Zero Air at 900psi, AMP FB04319 514.07 at 400 Tdewspan=20.00 CO2 zero 0.9482 -> .9479 Offset: -.96ppm CO2 span 1.0114 -> 1.0101 Offset: .74ppm H2O zero 0.8455 -> .8463 Offset: 5.4ppm H2O span 1.0264 -> 1.0236 Offset: .06ppm Notes: Used "514.00" as CO2 span point in the 7550 software. Touched up outside with white nail polish and glued the spike mounting disk back on. |
| LI-7500A 0035 | 2025-01-07 | Lab | Calibration | Lab | Last calibration: 2024-07-19 AGC=100.4 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.9kPa, Tair=25.4C, Tdew=2.86C Zero Air at 900psi, AMP FB04319 514.07 at 400 Tdewspan=20.00 CO2 zero 0.937 -> .9373 Offset: 1.19ppm CO2 span 1.0211 -> 1.017 Offset: 2.52ppm H2O zero 0.8999 -> .8979 Offset: -11.9ppm H2O span 1.0373 -> 1.0284 Offset: .19ppm Notes: Used "514.00" as CO2 span point in the 7550 software |
| CS616 13932-5 | 2024-12-18 | Lab none | Installed | Rush Ranch Soil Moisture | Installed at -8cm depth south of the southwest corner of tower at Rush Ranch as part of the refurbished met system |
| SP75 020854E-6-03-02-06862 | 2025-01-06 | Lab none | Loaned | Loaned none | Loaned to Patty for increased winter power at their Chico inter-comparison site. Picked up by Arshdeep and Rich. Paired with sn 024398E-1-26-04-99974 and triangular ground mounts |
| SQ75 024398E-1-26-04-99974 | 2025-01-06 | Lab none | Loaned | Loaned none | Loaned to Patty for increased winter power at their Chico inter-comparison site. Picked up by Arshdeep and Rich. Paired with sn 020854E-6-03-02-06862 and triangular ground mounts |
| SP75 020854E-6-03-02-06905 | 2025-01-06 | Lab none | Loaned | Loaned none | Loaned to Patty for increased winter power at their Chico inter-comparison site. Picked up by Arshdeep and Rich. |
| PTB101B V2420003 | 2024-12-18 | Lab none | Installed | Rush Ranch Barometer | Installed in met box at Rush Ranch as part of the refurbished met system |
| HMP35C 375061 | 2024-12-18 | Lab none | Installed | Rush Ranch RH & Temp | Installed on top northwest corner of scaffolding at Rush Ranch as part of the refurbished met system |
| HFP01 003073 | 2024-12-18 | Lab none | Installed | Rush Ranch Heat Flux Plate A | Installed at -2cm 3m south of southeast corner of tower at Rush Ranch as part of the refurbished met system |
| SPN1 SPN1-A333 | 2024-12-18 | Lab none | Installed | Rush Ranch Pyranometer Diffuse | Installed on top northeast side of scaffolding at Rush Ranch as part of the refurbished met system |
| TR-525M 23374-1298 | 2024-12-18 | Lab none | Installed | Rush Ranch Precipitation | Installed on top southeast corner of scaffolding at Rush Ranch as part of the refurbished met system |
| Quantum Q40954 | 2024-12-18 | Lab none | Installed | Rush Ranch PAR Sensor Outgoing | Installed on folding boom at Rush Ranch as part of the refurbished met system |
| Quantum Q40955 | 2024-12-18 | Lab none | Installed | Rush Ranch PAR Sensor Incoming | Installed on folding boom at Rush Ranch as part of the refurbished met system |
| CNR1 90268 | 2024-12-18 | Lab none | Installed | Rush Ranch Net Radiometer 4-way | Installed at end of folding boom at Rush Ranch as part of the refurbished met system |
| AM25T 4852 | 2024-12-18 | Lab none | Installed | Rush Ranch Multiplexer | Installed at Rush Ranch as part of the refurbished met system |
| CR1000 42656 | 2024-12-18 | Lab none | Installed | Rush Ranch Data Logger | Installed at Rush Ranch as part of the refurbished met system |
| CR1000 45312 | 2024-12-18 | Rush Ranch Data Logger | Removed | Lab none | Removed and prewired boxed sn 42656 swapped in place |
| NL115 12397 | 2024-11-14 | Lab none | Installed | Rush Ranch Interface | Installed in a box on the southeast corner of the scaffolding to collect phenocam images. |
| CR1000 45312 | 2024-11-14 | Lab none | Installed | Rush Ranch Data Logger | Installed in a box on the southeast corner of the scaffolding to collect phenocam images. |
| CAM-SEC5IR 0030F4D0A725 | 2024-11-14 | Lab none | Installed | Rush Ranch Camera | Installed on the top of the scaffolding looking west into the marsh. |
| GMP343 N2220007 | 2024-12-19 | Factory none | Received | Lab none | Returned from Vaisala after repair and calibration |
| EXO Central Wiper 24A100660 | 2024-12-10 | Factory none | Disposed | Disposed none | Disposed at the factory and replaced under warranty by sn 24L000786. Factory report below:
EXO CENTRAL WIPER SN# 24A100660 REPORTED SYMPTOM: EVALUATE/TEST/DRAWING TOO MUCH POWER TECHNICIAN NOTES: WIPER WILL BE REPLACED WITH NEW UNDER WARRANTY. ++++++++++++++++++++++++++++++++++++++++++++++ O-RING WEAR: NORMAL YSI RECOMMENDS HAVING WIPER MOTOR O-RINGS REPLACED AND LUBED EVERY 12 MOS TO PREVENT WATER LEAKAGE AND MOTOR SHAFT DAMAGE. ++++++++++++++++++++++++++++++++++++++++++++++ TEST AND CALIBRATES: FAIL PROBE WIPES AND PARKS: FAIL FIRMWARE VERSION UP TO DATE: FAIL REPLACE HEAD & MOTOR O-RINGS FINAL TEST |
| EXO Central Wiper 24A100660 | 2024-11-07 | Lab none | Shipped | Factory none | Sent back to the factory for inspection. Hopefully it will be replaced under warranty. |
| CR1000 42656 | 2024-12-09 | Lab none | Maintenance | Lab none | This data logger had a note about locking up. It seemed to have a program for high frequency flux data but not currently running. It was using OS v31 and its lithium battery was dead 0.15V. I replaced its lithium battery and updated its OS to the most recent v32.07 |
| RPI0W RPI0W-002 | 2024-12-04 | Lab none | Installed | Bouldin Alfalfa none | Installed in the Bouldin alfalfa/wheat field. The wheat sprouts are only a few cm tall. |
| RPI0W RPI0W-007 | 2024-12-04 | Lab none | Installed | Bouldin Alfalfa none | Installed in the Bouldin alfalfa/wheat field. The wheat sprouts are only a few cm tall. |
| HMP45A F1830005 | 2024-12-02 | Lab none | Tested | Lab none | Connected to a CR1000 and tested next to the HMP155 from WP for six days. Seems okay. See: https://biometlab.cnr.berkeley.edu/bmetdata/rtreport.php?screen=view&id=86 |
| HMP45A C4240049 | 2024-12-02 | Lab none | Tested | Lab none | Connected to a CR1000 and tested next to the HMP155 from WP for six days. Seems okay. See: https://biometlab.cnr.berkeley.edu/bmetdata/rtreport.php?screen=view&id=86 |
| HMP35C 375061 | 2024-12-02 | Lab none | Tested | Lab none | Connected to a CR1000 and tested next to the HMP155 from WP for six days. Seems okay. See: https://biometlab.cnr.berkeley.edu/bmetdata/rtreport.php?screen=view&id=86 |
| HMP35C P3630008 | 2024-12-02 | Lab none | Tested | Lab none | Connected to a CR1000 and tested next to the HMP155 from WP for six days. Seems okay. See: https://biometlab.cnr.berkeley.edu/bmetdata/rtreport.php?screen=view&id=86 |
| CR1000 59223 | 2024-11-22 | Lab none | Maintenance | Lab none | I replaced the internal lithium battery which was dead and updated the OS from v32.02 to v32.07. |
| EXO3S 23H107001 | 2024-07-24 | Lab none | Calibration | Lab none | Depth (m), Last cal: EXO sn 23H107001 EXO/Sensor Firmware: 1.0.86/3.1.3 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.000 m,10.280 m,0.000 m,0.000 m,20.652 °C Note: First calibration on new sensor. Calibration time 2024-07-24 15:22 so 0 is set to barometric pressure in Hilgard 205 at that time. |
| EXO Turbidity 24F102410 | 2024-07-25 | Lab none | Calibration | Lab none | Turbidity (FNU), Last cal: EXO sn 23H107001 EXO/Sensor Firmware: 1.0.86/3.0.5 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 FNU,-0.04 FNU,0.00 FNU,0.00 FNU,23.318 °C Pt2,124.00 FNU,131.81 FNU,124.00 FNU,0.00 FNU,23.157 °C Pt3,1010.00 FNU,983.43 FNU,1010.01 FNU,0.00 FNU,23.294 °C Note: First calibration on new sensor. |
| EXO Wiped Cond/Temp 24F100050 | 2024-07-25 | Lab none | Calibration | Lab none | Sp Cond (uS/cm),Last cal: EXO sn 23H107001 EXO/Sensor Firmware 1.0.86/3.0.5 CellConstant 0.47 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,5000.0 µS/cm,4954.6 µS/cm,5000.0 µS/cm,0.0 µS/cm,22.816 °C Note: First calibration on new sensor. Used USGS standard from Fondriest that expired Aug 2023. It was stored in fridge w/ cap taped and I brought it close to room temperature before calibration. |
| EXO pH-ORP 24G102326 | 2024-07-25 | Lab none | Calibration | Lab none | pH, Last cal: EXO sn 23H107001 EXO/Sensor Firmware: 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,7.01 pH,7.19 pH,7.01 pH,-10.9 mV,22.992 °C Pt2,10.06 pH,10.18 pH,10.06 pH,-186.1 mV,22.810 °C Pt3,4.00 pH,4.26 pH,4.00 pH,160.6 mV,22.822 °C 4-7Slope,4-7mVPerDecade,7-10Slope,7-10mVPerDecade 171.5 mV,56.98 mV,175.2 mV,57.43 Note: First calibration on a new sensor. Used opened standards from Dec 2023. |
| EXO pH-ORP 24G102326 | 2024-07-25 | Lab none | Calibration | Lab none | ORP (mV), Last Cal: EXO sn 23H107001 EXO/Sensor Firmware 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,223.0 mV,228.6 mV,223.0 mV,0.0 mV,23.893 °C Note: First calibration on a new sensor. Used Zobell solution (mixed 2022-09-23) in small brown plastic bottle. |
| EXO pH-ORP 24G102326 | 2024-10-22 | Lab none | Calibration | Lab none | pH, Last cal: 2024-07-25 EXO sn 23H107001 EXO/Sensor Firmware: 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,7.01 pH,7.03 pH,7.01 pH,-12.6 mV,21.535 °C Pt2,10.06 pH,10.08 pH,10.06 pH,-186.6 mV,22.141 °C Pt3,4.00 pH,4.01 pH,4.00 pH,160.2 mV,22.907 °C 4-7Slope,4-7mVPerDecade,7-10Slope,7-10mVPerDecade 172.8 mV,57.41 mV,174.1 mV,57.07 Note: Used opened standards from Dec 2023. |
| EXO pH-ORP 24G102326 | 2024-10-22 | Lab none | Calibration | Lab none | ORP (mV), Last Cal: 2024-07-25 EXO sn 23H107001 EXO/Sensor Firmware 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,226.7 mV,222.3 mV,226.7 mV,0.0 mV,23.160 °C Note: Used Zobell solution (mixed 2022-09-23) in small brown plastic bottle. |
| EXO Wiped Cond/Temp 24F100050 | 2024-10-22 | Lab none | Calibration | Lab none | Sp Cond (uS/cm),Last cal: 2024-07-25 EXO sn 23H107001 EXO/Sensor Firmware 1.0.86/3.0.5 CellConstant 0.47 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,5000.0 µS/cm, 4991.9 µS/cm,5000.0 µS/cm, 0.0 µS/cm,22.658 °C Note: Used USGS standard from Fondriest that expired Aug 2023. It was stored in fridge w/ cap taped and I brought it close to room temperature before calibration. |
| EXO Turbidity 24F102410 | 2024-10-22 | Lab none | Calibration | Lab none | Turbidity (FNU), Last cal: 2024-07-25 EXO sn 23H107001 EXO/Sensor Firmware: 1.0.86/3.0.5 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 FNU,-0.06 FNU,0.00 FNU,0.00 FNU,23.324 °C Pt2,124.00 FNU,123.12 FNU,124.00 FNU,0.00 FNU,22.559 °C Pt3,1010.00 FNU, 1004.19 FNU, 1010.01 FNU, 0.00 FNU, 22.612 °C Note: |
| EXO Wiped Cond/Temp 23D104030 | 2024-10-22 | Lab none | Calibration | Lab none | Sp Cond (uS/cm),Last cal: 2024-07-21 EXO sn 22C103416 EXO/Sensor Firmware 1.0.86/3.0.5 CellConstant 0.47 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,5000.0 µS/cm,5078.3 µS/cm,5000.0 µS/cm, 0.0 µS/cm,21.213 °C Note: Used USGS standard from Fondriest that expired Aug 2023. It was stored in fridge w/ cap taped and I brought it close to room temperature before calibration. |
| EXO Turbidity 22E106072 | 2024-10-22 | Lab none | Calibration | Lab none | Turbidity (FNU), Last cal: 2024-07-21
EXO sn 22C103416 EXO/Sensor Firmware: 1.0.86/3.0.4 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 FNU,0.33 FNU,0.00 FNU,0.00 FNU,23.484 °C Pt2,124.00 FNU,140.26 FNU,124.00 FNU,0.00 FNU,22.445 °C Pt3,1010.00 FNU, 1133.83 FNU, 1010.01 FNU, 0.00 FNU, 22.568 °C Note: |
| EXO fDOM 24F104438 | 2024-10-22 | Lab none | Calibration | Lab none | fDOM (QSU and RFU), Last cal: 2024-07-22 EXO sn 22C103416 EXO/Sensor Firmware: 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 QSU,0.10 QSU,0.00 QSU,0.00 QSU,23.760 °C Pt2,300.00 QSU,319.62 QSU,300.01 QSU,0.00 QSU,22.150 °C Notes: Calibration solution from 2024-07-21. First calibration on new sensor. ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 RFU,-.02 RFU,0.00 RFU,0.00 RFU,23.208 °C Pt2,100.0 RFU,106.05 RFU,100.00 RFU,0.00 RFU,22.127 °C Notes: Cal solution using QSE solution from 2024-07-20. |
| EXO fDOM 22C100780 | 2024-10-22 | Lab none | Calibration | Lab none | fDOM (QSU and RFU), Last cal: EXO sn 23H107001 EXO/Sensor Firmware: 1.0.86/3.0.0 ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 QSU,-1.75 QSU,0.00 QSU,0.00 QSU,23.325 °C Pt2,300.0 QSU,272.10 QSU,300.00 QSU,0.00 QSU,22.418 °C ,Standard,PreCal,PostCal,RawValue,Temp Pt1,0.00 RFU,-0.61 RFU,0.00 RFU,0.00 RFU,23.221 °C Pt2,100.00 RFU,91.28 RFU,100.00 RFU,0.00 RFU,22.440 °C Note: Made fresh calibration solution using QSE solution from 2024-07-20. Calibrated with a mess-up calibration solution yesterday so did a factory reset before today's calibration. |
| CTD-10 1782503941 | 2024-11-20 | Lab none | Disposed | Disposed none | Disposed of in e-waste. |
| CS450 20010769 | 2024-11-20 | Lab none | Tested | Lab none | Tested overnight in the lab and seems to work fine. It stopped working at WP around the time we started having power issues, so maybe the water level data was bad b/c of power issues, not sensor issues. The exterior cable has multiple cracks in it, so we may order a long piece of heat shrink to protect it. 20' cable. |
| CS451 70011234 | 2024-11-20 | Lab none | Tested | Lab none | Ran overnight in the lab and confirmed it is working. The outside cable has many cracks and the pigtail leads are shorter than usual, so the power wires probably have to be connected to the datalogger instead of a power strip so that the Data wire can still reach the C port. 15' cable. |
| CS451 70011236 | 2024-11-18 | Lab none | Tested | Lab none | Tested in the lab and definitely broken. Placed in the "Old Sensor" box in the sensor closet. |
| BB-Fab | 2024-11-15 | Rush Ranch Battery Bank | Upgrade | Rush Ranch Battery Bank | On about this data I the Patty upgrade this battery bank for her isotope campaign. There are six Duralast 24DC-DL batteries wired in parallel for a 12V system. These are group 24 deep cycle flooded batteries with 65Ah capacity. |
| CR23X 1751 | 2024-11-14 | Lab none | Maintenance | Lab none | First check of this data logger after salvage from RR annex location. The clock was set to 2009-01-01 (default?) the lithium battery is dead 0.48V. 99 watchdog errors, 99 skipped scans, 9 <12V errors. It's running OS v19 which is the most recent. I was able to download the existing program and saved it as RR_annex_retrieved_20241114.dll. Memory is scrambled - no thing reasonable downloaded. Maybe reloading the OS will clean it up. I'll replace it's lithium battery but it seems okay. |
| 425A 0843 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| 425A 0839 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| 425A 0846 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| 425A 0860 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| 425A 0852 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| 425A 0854 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| FMA RMT-200 08-0114 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| FMA RMT-200 05-0010 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| LAI-2000 PCA-1478 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| LAI-2000 PCA-0846 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| LI-6262 IRG3-1079 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| LI-6400 PSC-0785 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| LI-6400 PSC-2474 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| LI-6400 | 2024-11-13 | Lab none | For Resuse | Lab none | Marked for reuse |
| miniDOT 1219 | 2024-11-05 | Lab none | Installed | East End DO Sensor | Reinstalled after a trip to the lab for a clock reset, fresh desiccant, and new batteries. |
| LI-7500A 75H-2176 | 2024-11-06 | Lab none | Installed | Hill Slough Gas Analyzer CO2/H2O | Installed at Hill Slough to replace sn 0042 for calibration. |
| LI-7500A 0042 | 2024-11-06 | Hill Slough Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Hill Slough for calibration. Replaced by sn 75H-2176. |
| LI-7500A 0073 | 2024-11-06 | Lab none | Installed | Bouldin Alfalfa Gas Analyzer CO2/H2O | Installed at Bouldin Alfalfa to replace sn 75H-2667 for calibration. |
| LI-7500A 75H-2667 | 2024-11-06 | Bouldin Alfalfa Gas Analyzer CO2/H2O | Removed | Lab none | Removed from Bouldin Alfalfa for calibration. Replaced by sn 0073. |
| CR1000 45312 | 2024-11-08 | Lab none | Upgrade | Lab none | I am having trouble getting FTP and ping to work on this logger. I've ruled out problems with the NL115/116, cables and ethernet switch. I could connect to the CR1000 with an IP port. It was running OS v32.02 and the newest OS is v32.07. I updated the OS hoping it would wipe whatever setting might be interfering. Nope - no luck. All the hardware works just fine on another CR1000. |
| EXO Central Wiper 24A100660 | 2024-11-08 | Lab none | Tested | Lab none | Yesterday in the field, I saw an error message that said something like "the sensor on port 7 is drawing too much power," (central port where the wiper was installed). The wiper and depth data were 0 since our last data download, although the water quality parameters (fDOM, turbidity, conductivity, temperature) had reasonable data. Today I plugged the EXO2 in in the lab and all connected fine for about 10 seconds, until the Kor software had a pop-up window that said the instrument was disconnected. I tried disconnecting the wiper and leaving the three water quality sensors connected: the red LED on the sonde displayed the expected steady 1Hz blink and the Kor software can detect the instrument. When the wiper was installed, the red LED on the sonde flutters ~1Hz (not a distinct blink) and the Kor software cannot detect the instrument. I tested both the central port and another port on the side but the result was the same. I'll e-mail YSI tech support to see what they say. |
| CAM-SEC5IR 0030F4D0A725 | 2024-11-08 | Lab none | Upgrade | Lab none | I set up this Stardot camera with the latest PIT version by connecting it the router on my desk so it could talk to the internet. I edited the script files so that it sends the photos to a CR1000 card at 192.168.2.100 via FTP. camera IP address = 192.168.2.101 camera DNS = 192.168.2.1 |
| GMP343 N2220007 | 2024-11-04 | Lab none | Shipped | Factory none | Sent to Visala on quote Q-00284252, UPS tracking number 1Z0116959091064304 |
| GMP343 N2220007 | 2024-11-04 | Lab none | Tested | Lab none | I connected a DB9 connector white to pin 2, green to pin 3, and power to a lithium power pack, pink to +12V and gray to G and a spare brown wire between G and pin5 on the DB9. This allowed me to communicate with the probe via a serial terminal 19200,8,N,1. These are in POLL mode: ?? gets info, SEND id gets current reading, OPEN id put it in STOP MODE so you can issue ERRS to get error info. This one had E02 and E08 bad source, bad reading. Vaisala's web site has an automated repair quote process that had a flat repair fee for about $400 and a calibration fee of about $600. I'll send it for repair. |
| miniDOT 1219 | 2024-11-04 | Lab none | Maintenance | Lab none | Set the clock with miniDOT Control Rev 1.12. The error was -2652 seconds (-44.2 min). |
| U20-001-04 20005770 | 2024-10-24 | Rush Ranch Water Level A | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely used elsewhere. |
| LI-7700 TG1-0203 | 2024-10-24 | Lab none | Installed | Rush Ranch Gas Analyzer CH4 | Installed on new mount at the top of the main tower at Rush Ranch |
| LI-7550 AIU-1570 | 2024-10-24 | Lab none | Installed | Rush Ranch Interface | Installed on the main tower at Rush Ranch |
| LI-7500A 0418 | 2024-10-24 | Lab none | Installed | Rush Ranch Gas Analyzer CO2/H2O | Installed on new mount at the top of the main tower at Rush Ranch |
| WM 1590 120908 | 2024-10-24 | Lab none | Installed | Rush Ranch Anemometer | Installed on new mount at the top of the main tower at Rush Ranch |
| HFT3 H993105 | 2024-10-24 | Rush Ranch Heaf Flux Plate Annex B | Lost | Disposed none | Lost in the wetland |
| HFT3 H993102 | 2024-10-24 | Rush Ranch Heaf Flux Plate Annex A | Lost | Lab none | Lost in the wetland |
| CS616 13932-5 | 2024-10-24 | Rush Ranch Soil Moisture Annex | Removed | Lab none | Broken to be disposed of. |
| Quantum Q40959 | 2024-10-24 | Rush Ranch PAR Sensor Annex Outgoing | Removed | Lab none | Removed from the Annex tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| Quantum Q40956 | 2024-10-24 | Rush Ranch PAR Sensor Annex Incoming | Removed | Lab none | Removed from the Annex tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| SS-6-12V 12440075 | 2024-10-24 | Rush Ranch Solar Controller Annex | Removed | Lab none | Removed from the Annex tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| CR23X 1751 | 2024-10-24 | Rush Ranch Data Logger Annex | Removed | Lab none | Removed from the Annex location about 115m out in the wetland southwest of the tower. |
| WL-400-003 1202000485 | 2024-10-24 | Rush Ranch Water Level Annex | Removed | Lab none | Removed from the Annex tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| U20-001-04 20005768 | 2024-10-24 | Rush Ranch Water Level C | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely used elsewhere. |
| U20-001-04 20005777 | 2024-10-24 | Rush Ranch Water Level B | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely used elsewhere. |
| 1561-LID-040/W 201906 | 2024-10-24 | Rush Ranch Anemometer | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| CAM-SEC5IR 0030F4D0A725 | 2024-10-24 | Rush Ranch Camera | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| 7900-600 SMART2-00480 | 2024-10-24 | Rush Ranch Interface SmartFlux | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. Probably will not be returned to the tower. |
| LI-7500RS 75H-1653 | 2024-10-24 | Rush Ranch Gas Analyzer CO2/H2O | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| LI-7550 AIU-2023 | 2024-10-24 | Rush Ranch Interface | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |
| Quantum Q40954 | 2024-10-24 | Rush Ranch PAR Sensor Outgoing | Removed | Lab none | Removed from the main tower at Rush Ranch with the handoff of the site. To be cleaned up, tested and likely returned to the tower. |