| Rec No. | Date | Loc From | Title | Loc To | Notes |
|---|
| 6412 |
2023-09-18 |
Lab none |
Loaned |
Loaned none |
Loaned to Gracie Pearsall at UCSC for a informational display at Elkhorn Reserve |
| 4000 |
2019-06-13 |
Lab none |
Tested |
Lab none |
Tested but we probably can't use this sensor any more. We put in new AA lithium batteries, and the miniDOT was able to power up, but the LED light continuously blinks 2x, "card error." We tried re-formatting the card, using another 2GB card previously used in a miniDOT (could have been a bad card), and then with a good SD card at EE. In all cases, the LED status light still indicated a "card error." |
| 3999 |
2019-05-23 |
Mayberry DO Sensor E |
Removed |
Lab none |
Brought back to the lab for testing. The o-ring was warped and it was damp inside. There was some corrosion on the board and the batteries were dead. |
| 3997 |
2018-11-28 |
Mayberry DO Sensor E |
Maintenance |
Mayberry DO Sensor E |
Swapped 2x AA lithium batteries |
| 3965 |
2018-10-04 |
Mayberry DO Sensor E |
Notes |
Mayberry DO Sensor E |
Measured at -45 cm. |
| 4529 |
2018-02-28 |
Mayberry DO Sensor E |
Moved |
Mayberry DO Sensor E |
We're guessing this is when the sensor was moved from -62 to -45cm. |
| 3964 |
2017-10-13 |
Lab none |
Installed |
Mayberry DO Sensor E |
After the barnacle was removed in the lab, reinstalled at MB on the floating boom, lower position. |
| 3963 |
2017-08-16 |
Mayberry DO Sensor E |
Removed |
Lab none |
Removed from lower position (-62 cm) on floating boom and brought in to the lab for barnacle removal. |
| 3959 |
2017-05-25 |
Mayberry DO Sensor D |
Moved |
Mayberry DO Sensor E |
Moved from static boom (upper position, -10 cm based on water level on 2017-05-10) to floating boom (lower position, -62 cm). |
| 3955 |
2017-05-10 |
Mayberry DO Sensor E |
|
Mayberry DO Sensor D |
sn 1220 moved from middle position (-38 cm based on water level on 2017-02-23) to upper position (-10cm based on water level on 2017-05-10) with the other 2 miniDOTs. |
| 2634 |
2017-02-23 |
Mayberry DO Sensor F |
Moved |
Mayberry DO Sensor E |
Moved from the bottom position on the fence post in the channel to the middle position on the new water sensor boom. |
| 2498 |
2016-10-11 |
Mayberry DO Sensor D |
Moved |
Mayberry DO Sensor F |
Due to the lowering of the water to flush the salt, this sensor was no longer in the water, but could not be removed because it was rusted to the chain. It was moved to the bottom/lower location by inverting the chain. |
| 1604 |
2014-10-16 |
Lab none |
Installed |
Mayberry DO Sensor D |
Installed at 26cm below the water surface on the fence post in the channel. |
| 1601 |
2014-10-09 |
West Pond DO Sensor A |
Removed |
Lab none |
Removed from West Pond for installation at Mayberry where a longer profile is possible. |
| 1588 |
2014-09-25 |
Lab none |
Installed |
West Pond DO Sensor A |
Installed at West Pond in a profile at 13cm above soil in water column. |
| 1569 |
2014-09-24 |
Lab none |
Maintenance |
Lab none |
Using the miniDOTControl program I set the time and set the sample interval to one minute. |
