Equipment and Calibration

Equipment history at Tonzi

| ALL | | Anemometer || Barometer || Battery Bank || Camera || CO2 Probe || Data Logger || Forced Diffusion || Gas Analyzer || Heat Flux Plate || Infrared Temperature || Interface || LED sensor || Moisture Point || Multiplexer || Narrow Band || Net Radiometer || PAR Sensor || Precipitation || Radio || RH & Temp || Soil Moisture Probe || Soil Water Potential || Solar Controller || Solar Panel || Water Level || Weather Station |

SELECT a.recno, a.eh_date, a.eh_loc1, a.eh_loc2, IF(a.eh_loc2=:loc, a.eh_locref2, a.eh_locref1) AS ref, a.eh_locref2, a.eh_title, a.eh_notes, a.eh_id, b.serialno, b.equip, b.modelno FROM equiphist a INNER JOIN equiplist b ON a.eh_id=b.recno WHERE (a.eh_loc1=:loc1 OR a.eh_loc2=:loc2) ORDER BY b.equip, a.eh_date, field(a.eh_title,'Calibration', 'Removed', 'Installed')

Date	Serial No.	Model	Action	Ref	Notes
Anemometer
2015-04-08	0846	425A	Installed		Installed at 7.56m agl in a wind profile near the Floor tower.
2015-04-08	0843	425A	Installed		Installed at 5.42m agl in a wind profile near the Floor tower.
2015-04-08	0860	425A	Installed		Installed at 3.89m agl in a wind profile near the Floor tower.
2015-04-08	0839	425A	Installed		Installed at ~2.0m agl in a wind profile near the Floor tower.
2015-04-08	0852	425A	Installed		Installed at ~1.2m agl in a wind profile near the Floor tower.
2015-04-08	0854	425A	Installed		Installed at ~0.1m agl in a wind profile near the Floor tower.
2015-04-29	0860	425A	Removed		Removed from the 3.89m location on the wind profile due to bad data. This is the sonic the was banged previously.
2015-12-23	0852	425A	Removed		Removed from the bottom location of the wind profile near the Floor tower.
2015-12-23	0839	425A	Removed		Removed from the 3rd from bottom location of the wind profile near the Floor tower.
2015-12-23	0846	425A	Removed		Removed from the top location of the wind profile near the Floor tower.
2015-12-23	0843	425A	Removed		Removed from the 2nd from top location of the wind profile near the Floor tower.
Barometer
2018-01-15	B0310006	PTB101B	Installed		Installed in a box just below the 3rd lowest location of the tower co2 profile. This sensor will be used to give real time pressure to the GMP343s.
Battery Bank
2010-01-08	BB-TZ_soilco2	BB-Fab	Upgrade		I replaced both pairs of batteries in new pairs marker November 2009.
2010-01-27	BB-TZ_soilco2	BB-Fab	Maintenance		I moved and combined the east 24V system with the west 24V system. Four panels in two pairs now feed two pairs of batteries through one charge controller.
2017-01-17	BB-TT	BB-Fab	Maintenance		The Tower has been losing power over night recently. All the batteries were disconnected and tested them with the load tester. Four batteries tested bad. We removed them and reconnected the others.
2017-07-12	BB-TT	BB-Fab	Maintenance		I swapped out the eight batteries remaining in the Tower battery bank sn BB-TT and replaced them with twelve new Duracell deep cycle marine group 27 lead acid batteries SLI27MDC from Batteries Plus. It’s still a 12V system pending a major rewiring in the future.
2017-09-28	BB-TT	BB-Fab	Upgrade		The Tonzi Tower battery bank was rewired to be a 24V system for the upgrade of the solar power system.
2018-06-26	BB-TZ_soilco2	BB-Fab	Maintenance		The top of the plates were visible in almost all cells. I refilled them all with DI water.
2018-12-13	BB-TZ_soilco2	BB-Fab	Upgrade		This system has been failing overnight partly because one set of Vaisala probes have not been cycling off. I also added to old batter most recently used on East End.
2019-07-16	BB-TZ_soilco2	BB-Fab	Maintenance		There are six batteries in three pairs for a 24V system – the original four plus two more we added last winter. Two of the originals test a little weak with the load tester so I disconnected them from the bank.
2019-08-22	BB-TZ_soilco2	BB-Fab	Upgrade		Six old weak batteries (four currently connected) were brought back to the lab and four new Duracell deep cycle flooded group 27 batteries were installed in pairs for a 24V system. The new batteries have 09/19 (Sept/2019) stickers.
2020-09-01	BB-TT	BB-Fab	Maintenance	none	The batteries were bone dry, 8-9 gallons of water into the 12 batteries. 4-5 batteries on the east side of south row got purified water instead of distilled. Two western most batteries tested bad with load tester and were brought in. The rest tested good, were reconnected and powered up.
2021-06-24	BB-TZ_soilco2	BB-Fab	Maintenance	Battery Bank soil co2	Added about 1.5 gallons of DI to the four batteries in total. No plates exposed.
2022-08-05	BB-TZ_soilco2	BB-Fab	Maintenance	Battery Bank soil co2	The batteried in this bank have been temporarily removed to power the Tower. Likely this bank will be repopulated to power the OSU-SP1 system and a couple FD chambers as the Vaisala soil CO2 system is decommissioned.
2022-08-25	BB-TZ_soilco2	BB-Fab	Maintenance	Battery Bank soil co2	This battery bank had been without batteries since its batteries were moved to the Tower a few weeks ago. I installed three old batteries from the Floor system that tested ok with the load tester. I rewired the two larger solar panels to 12V. The two smaller panels had there leads chewed and I left them disconnected for now.
2023-03-01	BB-TZ_soilco2	BB-Fab	Replaced	Battery Bank soil co2	I brought the three batteries last remove from HS and put them under the solar panels. I rewired all the panels into a terminal strip. I used one of the old batteries for the fence charger and brought the rest in.
2023-11-13	BB-TF	BB-Fab	Upgrade	Battery Bank Floor	We removed four flooded batteries that came from the Tower. Two are probably still good. The other two seemed to be internally shorted. Four new group 27 AGM batteries were installed.
2024-05-15	BB-TZ_soilco2	BB-Fab	Upgrade	Battery Bank soil co2	I replaced the three flooded batteries in the Soil CO2 battery bank with two new SLA group 27 batteries. The cows had chewed up all the wiring. I replaced all the wires. Now only the two larger 40W panels are connect resulting in about 4.5A. The charge controller is only 6A. The new power line runs to the OSU SP1 box.
Camera
2011-10-18	0030F4D0A167	NULL	Installed		Installed on the Tonzi tower to cover the same area as the existing webcam. The camera is mounted about 20m agl and is pointing about 310deg true and 20deg down from horizontal. Horizontal FOV is about 70deg.
2018-06-01	48013741	A325sc	Installed	Camera Thermal	Installed on a tripod near the Floor site pointing north.
2018-07-18	48013741	A325sc	Moved	Camera Thermal	The camera was moved from its tripod near the Floor site to the northwest corner on the Tower 18m agl. The camera is pointed to the north.
2020-09-01	48013741	A325sc	Removed	Camera Thermal	Removed from the Tower because it was not responding. It seemed to power up okay but its power indicator was solid red indicating an error.
CO2 Probe
2003-02-17	Y0850004	GMP221	Installed	CO2 Probe Open Profile -0.16	Installed at Tonzi in the east open set at 16cm deep.
2003-03-17	Y0710013	GMP221	Installed	CO2 Probe Tree1 Profile -0.16	Installed at Tonzi in the west under canopy set at 16cm deep.
2005-02-17	Z2720014	GMP222	Location	CO2 Probe Open Profile -0.02	Location noted at Tonzi in Open (East) profile at -2cm
2005-02-17	Z2720011	GMP222	Location	CO2 Probe Open Profile -0.04	Location noted at Tonzi in Open (East) profile at -4cm
2005-02-17	Z2720012	GMP222	Location	CO2 Probe Open Profile -0.08	Location noted at Tonzi in Open (East) profile at -8cm
2005-02-17	X4840007	GMP222	Location	CO2 Probe Tree1 Profile -0.02	Location noted at Tonzi in Tree 1 (West) profile at -2cm
2005-02-17	X1920001	GMP222	Location	CO2 Probe Tree1 Profile -0.08	Location noted at Tonzi in Tree 1 (West) profile at -8cm - listed as probe #2
2005-02-17	X1520002	GMP221	Location	CO2 Probe Tree1 Profile -0.16	Location noted at Tonzi in Tree 1 (West) profile at -16cm - listed as probe #3
2005-02-17	Y0710013	GMP221	Location	CO2 Probe Tree1 Profile -0.04	Location noted at Tonzi in Tree 1 (West) profile at -4cm - listed as probe #4
2005-05-16	Y0850004	GMP221	Removed	CO2 Probe Open Profile -0.16	Removed from Tonzi in the east open area set at 16cm deep
2005-05-16	Y4110008	GMP221	Removed		Removed from Tonzi - location at Tonzi unknown
2008-03-06	X3830001	GMP222	Installed	CO2 Probe Open Profile -0.02	Installed in the East open grass profile at -2cm. mV and ppm readings in air were recorded before installation.
2008-03-06	X4840007	GMP222	Installed	CO2 Probe Open Profile -0.04	Installed in the East open grass profile at -4cm. mV and ppm readings in air were recorded before installation.
2008-03-06	Z2720014	GMP222	Installed	CO2 Probe Open Profile -0.08	Installed in the East open grass profile at -8cm. mV and ppm readings in air were recorded before installation.
2008-03-06	X1920001	GMP222	Installed	CO2 Probe Open Profile -0.16	Installed in the East open grass profile at -16cm. mV and ppm readings in air were recorded before installation.
2008-03-06	Z2720013	GMP222	Installed	CO2 Probe Tree1 Profile -0.02	Installed in the Wast under tree profile at -2cm. mV and ppm readings in air were recorded before installation.
2008-03-06	X5050014	GMP222	Installed	CO2 Probe Tree1 Profile -0.04	Installed in the Wast under tree profile at -4cm. mV and ppm readings in air were recorded before installation.
2008-03-06	Z2720011	GMP222	Installed	CO2 Probe Tree1 Profile -0.08	Installed in the Wast under tree profile at -8cm. mV and ppm readings in air were recorded before installation.
2008-03-06	Z2720012	GMP222	Installed	CO2 Probe Tree1 Profile -0.16	Installed in the Wast under tree profile at -16cm. mV and ppm readings in air were recorded before installation.
2010-01-08	X3830001	GMP222	Location	CO2 Probe Tree1 Profile -0.02	Pulled out for ambient air reading and put back.
2010-01-08	X4840007	GMP222	Location	CO2 Probe Tree1 Profile -0.04	Pulled out for ambient air reading and put back.
2010-01-08	Z2720014	GMP222	Location	CO2 Probe Tree1 Profile -0.08	Pulled out for ambient air reading and put back.
2010-01-08	X1920001	GMP222	Location	CO2 Probe Tree1 Profile -0.16	Pulled out for ambient air reading and put back.
2010-01-08	Z2720013	GMP222	Location	CO2 Probe Open Profile -0.02	Pulled out for ambient air reading and put back.
2010-01-08	X5050014	GMP222	Location	CO2 Probe Open Profile -0.04	Pulled out for ambient air reading and put back.
2010-01-08	Z2720011	GMP222	Location	CO2 Probe Open Profile -0.08	Pulled out for ambient air reading and put back.
2010-01-08	Z2720012	GMP222	Location	CO2 Probe Open Profile -0.16	Pulled out for ambient air reading and put back.
2012-02-16	Z2720013	GMP222	Installed	CO2 Probe Tree1 Profile -0.02	Installed at Tonzi in the Tree1 set at -2cm
2012-02-16	X5050014	GMP222	Installed	CO2 Probe Tree1 Profile -0.04	Installed at Tonzi in the Tree1 set at -4cm
2012-02-16	Z2720011	GMP222	Installed	CO2 Probe Tree1 Profile -0.08	Installed at Tonzi in the Tree1 set at -8cm
2012-02-16	X4840007	GMP222	Installed	CO2 Probe Open Profile -0.04	Installed at Tonzi in the Open set at -4cm
2012-02-16	Z2720014	GMP222	Installed	CO2 Probe Open Profile -0.08	Installed at Tonzi in the Open set at -8cm
2012-02-16	Z2720012	GMP222	Installed	CO2 Probe Open Profile -0.02	Installed at Tonzi in the Open set at -2cm. This was supposed to be sn X3830001 but that probe was not working and so was returned to the lab.
2012-03-02	Z2720012	GMP222	Installed	CO2 Probe Tree2 Profile -0.02	Installed at Tonzi in the Tree2 set at -2cm
2012-03-02	Y2009109	GMP222	Installed	CO2 Probe Tree2 Profile -0.04	Installed at Tonzi in the Tree2 set at -4cm
2012-03-02	X1920001	GMP222	Installed	CO2 Probe Tree2 Profile -0.08	Installed at Tonzi in the Tree2 set at -8cm
2012-03-02	F4960019	GMT221	Installed	CO2 Probe Tree2 Profile -0.02	Installed at Tonzi in the Tree2 set at -2cm
2014-01-24	Z2720013	GMP222	Removed	CO2 Probe Tree1 Profile -0.02	Removed from Tonzi tree #1 at -2cm for lab calibration
2014-01-24	X5050014	GMP222	Removed	CO2 Probe Tree1 Profile -0.04	Removed from Tonzi tree #1 at -4cm for lab calibration
2014-01-24	Z2720011	GMP222	Removed	CO2 Probe Tree1 Profile -0.08	Removed from Tonzi tree #1 at -8cm for lab calibration
2014-01-24	Z2720012	GMP222	Removed	CO2 Probe Open Profile -0.02	Removed from Tonzi open at -2cm for lab calibration
2014-01-24	X4840007	GMP222	Removed	CO2 Probe Open Profile -0.04	Removed from Tonzi open at -4cm for lab calibration
2014-01-24	Z2720014	GMP222	Removed	CO2 Probe Open Profile -0.08	Removed from Tonzi open at -8cm for lab calibration
2014-01-24	F4960019	GMT221	Removed	CO2 Probe Tree2 Profile -0.02	Removed from Tonzi tree #2 at -2cm for lab calibration
2014-01-24	Y2009109	GMP222	Removed	CO2 Probe Tree2 Profile -0.04	Removed from Tonzi tree #2 at -4cm for lab calibration
2014-01-24	X1920001	GMP222	Removed	CO2 Probe Tree2 Profile -0.08	Removed from Tonzi tree #2 at -8cm for lab calibration
2014-01-29	Z2720012	GMP222	Installed	CO2 Probe Open Profile -0.02	Installed at Tonzi in the Open profile at -2cm with new U-shaped tops on the PVC enclosures
2014-01-29	X4840007	GMP222	Installed	CO2 Probe Open Profile -0.04	Installed at Tonzi in the Open profile at -4cm with new U-shaped tops on the PVC enclosures
2014-01-29	F4960020	GMT221	Installed	CO2 Probe Open Profile -0.08	Installed at Tonzi in the Open profile at -8cm with new U-shaped tops on the PVC enclosures
2014-01-29	Z2720013	GMP222	Installed	CO2 Probe Tree1 Profile -0.02	Installed at Tonzi in the Tree 1 profile at -2cm with new U-shaped tops on the PVC enclosures
2014-01-29	X5050014	GMP222	Installed	CO2 Probe Tree1 Profile -0.04	Installed at Tonzi in the Tree 1 profile at -4cm with new U-shaped tops on the PVC enclosures
2014-01-29	G0150036	GMT221	Installed	CO2 Probe Tree1 Profile -0.08	Installed at Tonzi in the Tree 1 profile at -8cm with new U-shaped tops on the PVC enclosures
2014-03-18	Z2720013	GMP222	Moved	CO2 Probe Tree1 Profile -0.04	At Tonzi in the Tree 1 profile this probe was moved from the -2cm location to -4cm
2014-03-18	X5050014	GMP222	Moved	CO2 Probe Tree1 Profile -0.02	At Tonzi in the Tree 1 profile this probe was moved from the -4cm location to -2cm
2014-03-27	Z2720012	GMP222	Moved	CO2 Probe Tree2 Profile -0.04	This probe in the Tonzi Open profile was moved from the -2cm location to the Tree2 profile -4cm
2014-03-27	X4840007	GMP222	Moved	CO2 Probe Tree2 Profile -0.02	This probe in the Tonzi Open profile was moved from the -4cm location to the Tree2 profile -2cm
2014-03-27	F4960020	GMT221	Moved	CO2 Probe Tree2 Profile -0.08	This probe in the Tonzi Open profile was moved from the -8cm location to the Tree2 profile -8cm
2014-04-08	K1310104	GMP222	Installed	CO2 Probe Open Profile -0.02	Installed at Tonzi in the Open profile at -2cm. not clear if it replaced another probe.
2014-04-08	K1310103	GMP222	Installed	CO2 Probe Open Profile -0.04	Installed at Tonzi in the Open profile at -4cm. not clear if it replaced another probe.
2014-04-08	K1310102	GMP222	Installed	CO2 Probe Open Profile -0.08	Installed at Tonzi in the Open profile at -8cm. not clear if it replaced another probe.
2014-12-09	K1310102	GMP222	Location	CO2 Probe Open Profile -0.02	Tonzi Open profile at -2cm
2014-12-09	K1310103	GMP222	Location	CO2 Probe Open Profile -0.04	Tonzi Open profile at -4cm
2014-12-09	K1310104	GMP222	Location	CO2 Probe Open Profile -0.08	Tonzi Open profile at -8cm
2014-12-09	X5050014	GMP222	Location	CO2 Probe Tree1 Profile -0.02	Tonzi Tree1 profile at -2cm
2014-12-09	Z2720013	GMP222	Location	CO2 Probe Tree1 Profile -0.04	Tonzi Tree1 profile at -4cm
2014-12-09	G0150036	GMT221	Location	CO2 Probe Tree1 Profile -0.08	Tonzi Tree1 profile at -8cm
2014-12-09	X4840007	GMP222	Location	CO2 Probe Tree2 Profile -0.02	Tonzi Tree2 profile at -2cm
2014-12-09	F4960020	GMT221	Location	CO2 Probe Tree2 Profile -0.08	Tonzi Tree2 profile at -8cm
2014-12-09	Z2720012	GMP222	Removed	CO2 Probe Tree1 Profile -0.04	this probe was at Tonzi Tree2 profile at -4cm, notes say it was swapped but no serial number of the new probe
2015-11-03	X5050014	GMP222	Removed	CO2 Probe Tree1 Profile -0.02	Removed from the Tonzi Tree 1 profile at -2cm due to bad readings. Replaced by sn L2010069
2015-11-03	L2010069	GMM222	Installed	CO2 Probe Tree1 Profile -0.02	Installed in the Tonzi Tree 1 profile at -2cm to replace sn X5050014
2016-02-04	K1310102	GMP222	Removed	CO2 Probe Open Profile -0.02	Removed from Tonzi Open profile at -2cm for calibration
2016-02-04	K1310103	GMP222	Removed	CO2 Probe Open Profile -0.04	Removed from Tonzi Open profile at -4cm for calibration
2016-02-04	K1310104	GMP222	Removed	CO2 Probe Open Profile -0.08	Removed from Tonzi Open profile at -8cm for calibration
2016-02-04	L2010069	GMM222	Removed	CO2 Probe Tree1 Profile -0.02	Removed from Tonzi Tree profile at -2cm for calibration
2016-02-04	Z2720013	GMP222	Removed	CO2 Probe Tree1 Profile -0.04	Removed from Tonzi Tree profile at -4cm for calibration
2016-02-04	G0150036	GMT221	Removed	CO2 Probe Tree1 Profile -0.08	Removed from Tonzi Tree profile at -8cm for calibration
2016-02-04	Z2720014	GMP222	Removed	CO2 Probe Tree2 Profile -0.02	Removed from Tonzi Tree 2 profile at -2cm for calibration
2016-02-04	Z2720012	GMP222	Removed	CO2 Probe Tree2 Profile -0.04	Removed from Tonzi Tree 2 profile at -4cm for calibration
2016-02-04	F4960020	GMT221	Removed	CO2 Probe Tree2 Profile -0.08	Removed from Tonzi Tree 2 profile at -8cm for calibration
2016-02-23	K1310102	GMP222	Installed	CO2 Probe Open Profile -0.02	Installed in the Tonzi Open profile at -2cm after lab calibration.
2016-02-23	Z2720015	GMP222	Installed	CO2 Probe Open Profile -0.04	Installed in the Tonzi Open profile at -4cm after lab calibration.
2016-02-23	K1340006	GMP221	Installed	CO2 Probe Open Profile -0.08	Installed in the Tonzi Open profile at -8cm after lab calibration.
2016-02-23	L2010069	GMM222	Installed	CO2 Probe Tree1 Profile -0.02	Installed in the Tonzi Tree 1 profile at -2cm after lab calibration.
2016-02-23	G0150035	GMT221	Installed	CO2 Probe Tree1 Profile -0.04	Installed in the Tonzi Tree 1 profile at -4cm after lab calibration.
2016-02-23	G0150036	GMT221	Installed	CO2 Probe Tree1 Profile -0.08	Installed in the Tonzi Tree 1 profile at -8cm after lab calibration.
2016-02-23	Z2720012	GMP222	Installed	CO2 Probe Tree2 Profile -0.02	Installed in the Tonzi Tree 2 profile at -2cm after lab calibration.
2016-02-23	K1310104	GMP222	Installed	CO2 Probe Tree2 Profile -0.04	Installed in the Tonzi Tree 2 profile at -4cm after lab calibration.
2016-02-23	F4960020	GMT221	Installed	CO2 Probe Tree2 Profile -0.08	Installed in the Tonzi Tree 2 profile at -8cm after lab calibration.
2017-08-25	X4840007	GMP222	Notes		We removed the CO2 probe at the Tree 2 profile at -2 cm position. The probe was sn Z2720014. Not sure where sn X4840007 is.
2017-08-25	Z2720012	GMP222	Notes		Removed CO2 probe from Tonzi Tree2 profile at -2 cm. It was sn Z2720014, not sn Z2720012. Not sure where sn Z2720012 is.
2017-08-25	K1310102	GMP222	Removed	CO2 Probe Open Profile -0.02	Removed from Tonzi Open profile at -2 cm position for calibration
2017-08-25	Z2720015	GMP222	Removed	CO2 Probe Open Profile -0.04	Removed from Tonzi Open profile at -4 cm position for calibration
2017-08-25	K1340006	GMP221	Removed	CO2 Probe Open Profile -0.08	Removed from Tonzi Open profile at -8 cm position for calibration
2017-08-25	L2010069	GMM222	Removed	CO2 Probe Tree1 Profile -0.02	Removed from Tonzi Tree 1 profile at -2 cm position for calibration
2017-08-25	G0150035	GMT221	Removed	CO2 Probe Tree1 Profile -0.04	Removed from Tonzi Tree 1 profile at -4 or -8 cm position for calibration. Probe labeled 16.
2017-08-25	G0150036	GMT221	Removed	CO2 Probe Tree1 Profile -0.08	Removed from Tonzi Tree 1 profile at -4 or -8 cm position for calibration. Probe labeled 8.
2017-08-25	K1310104	GMP222	Removed	CO2 Probe Tree2 Profile -0.04	Removed from Tonzi Tree 2 profile at -4 cm position for calibration
2017-08-25	F4960020	GMT221	Removed	CO2 Probe Tree2 Profile -0.08	Removed from Tonzi Tree 2 profile at -8 cm position for calibration
2017-08-25	Z2720014	GMP222	Removed	CO2 Probe Tree2 Profile -0.02	Removed from Tonzi Tree 2 profile at -2 cm position for calibration
2017-09-14	K1310104	GMP222	Installed	CO2 Probe Open Profile -0.02	Installed at Tonzi in the Open profile at -2cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	Z2720015	GMP222	Installed	CO2 Probe Open Profile -0.04	Installed at Tonzi in the Open profile at -4cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	K1340006	GMP221	Installed	CO2 Probe Open Profile -0.08	Installed at Tonzi in the Open profile at -8cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	G0150037	GMT221	Installed	CO2 Probe Open Profile -0.16	Installed at Tonzi in the Open profile at -16cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	L2010069	GMM222	Installed	CO2 Probe Tree1 Profile -0.02	Installed at Tonzi in the Tree 1 profile at -2cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	G0150035	GMT221	Installed	CO2 Probe Tree1 Profile -0.04	Installed at Tonzi in the Tree 1 profile at -4cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	G0150036	GMT221	Installed	CO2 Probe Tree1 Profile -0.08	Installed at Tonzi in the Tree 1 profile at -8cm after lab calibration. Using old tube at -8cm.
2017-09-14	Y2009100	GMP221	Installed	CO2 Probe Tree1 Profile -0.16	Installed at Tonzi in the Tree 1 profile at -16cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	Z2720014	GMP222	Installed	CO2 Probe Tree2 Profile -0.02	Installed at Tonzi in the Tree 2 profile at -2cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	K1350103	GMP222	Installed	CO2 Probe Tree2 Profile -0.04	Installed at Tonzi in the Tree 2 profile at -4cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	F4960020	GMT221	Installed	CO2 Probe Tree2 Profile -0.08	Installed at Tonzi in the Tree 2 profile at -8cm after lab calibration. This is a new installation with new holes dug.
2017-09-14	Y0850004	GMP221	Installed	CO2 Probe Tree2 Profile -0.16	Installed at Tonzi in the Tree 2 profile at -16cm after lab calibration. This is a new installation with new holes dug.
2018-01-15	N2220007	GMP343	Installed		Installed at the lowest location in the tower co2 profile - not running yet due to data logger failure.
2018-01-15	N2210010	GMP343	Installed		Installed at the 2nd lowest location in the tower co2 profile - not running yet due to data logger failure.
2018-01-15	N2210009	GMP343	Installed		Installed at the 3rd lowest location in the tower co2 profile - not running yet due to data logger failure.
2018-02-07	N2220008	GMP343	Installed		Installed at the top location on the Tonzi Tower in the new Vaisala co2 Profile.
2019-11-19	G0150037	GMT221	Removed	CO2 Probe Open Profile -0.16	Removed from the deepest (-16cm) location in the Open soil co2 profile because its measurement was railed. This is a 3% probe and was replaced by a 1% probe.
2019-11-19	K1310102	GMP222	Installed	CO2 Probe Open Profile -0.16	Installed in the deepest (-16cm) location in the Open soil co2 profile to replace a 3% probe that was railed. This is a 1% probe.
2023-01-06	N2220008	GMP343	Removed	CO2 Probe Tower Profile 23	Removed from the top of the tower. This sensor has not been working for a while. I don't see any issues - brought in for testing.
2024-02-09	N2220007	GMP343	Removed	CO2 Probe Tower Profile 0.35	Removed from the lowest location on the Tower due to bad readings, cow chewed cable and to be calibrated
2024-02-09	N2210010	GMP343	Removed	CO2 Probe Tower Profile 1.8	Removed from the lower mid location on the Tower due to bad readings and to be calibrated
2024-02-09	N2210009	GMP343	Removed	CO2 Probe Tower Profile 6	Removed from the upper mid location on the Tower due to bad readings and to be calibrated
2024-02-27	N2220007	GMP343	Installed	CO2 Probe Tower Profile 0.35	Reinstalled in the bottom location of the Tower co2 profile after testing in the lab. New cable.
2024-02-27	N2210010	GMP343	Installed	CO2 Probe Tower Profile 1.8	Reinstalled in the lower-mid location of the Tower co2 profile after testing in the lab.
2024-02-27	N2210009	GMP343	Installed	CO2 Probe Tower Profile 6	Reinstalled in the upper-mid location of the Tower co2 profile after testing in the lab.
2024-02-27	N2220008	GMP343	Installed	CO2 Probe Tower Profile 23	Reinstalled in the top location of the Tower co2 profile after testing in the lab. Reinstalled cable.
2024-04-22	N2210009	GMP343	Removed	CO2 Probe Tower Profile 6	Not sending sensible data. Not sure why. Brought in for testing.
2024-06-19	N2210009	GMP343	Installed	CO2 Probe Tower Profile 6	Reinstalled in location #3 (6m) of the Tower co2 profile.
2024-10-10	N2220007	GMP343	Removed	CO2 Probe Tower Profile 0.35	Removed from the lowest position in the Tower CO2 profile. This sensor has bad CO2 readings. Occasionally restarting the sensor seemed to fix it but not this time. Need to check the data and test it in the lab.
Data Logger
2002-06-20	2301	CR23X	Installed	Data Logger Soil CO2	Installed with the initiation of soil CO2 gradient measurements
2010-02-10	38347	CR10X	Removed		This data logger was removed from Tonzi. It was used for sap flow just west of the floor tower. AM416 sn 14049 was removed with it. Wiring panel is 28250.
2010-03-16	25799	CR10X	Installed		This data logger was installed with new supplemental radiation and air temperature sensor inside the floor cow fense. Problems getting final storage data dumped - will have it swapped out by next visitor.
2010-03-19	20140	CR10X	Installed		Given to Siyan to install in the supplemental solar radiation measurements near the tram and floor system.
2010-03-21	25799	CR10X	Removed		This data logger was swapped out by Siyan from the floor supplemental radiation and temperature system. Final storage data is corrupt.
2010-12-09	20139	CR10X	Removed		This data logger was removed with the IRT sensors from Tonzi.
2011-02-03	20140	CR10X	Removed		Removed from Tonzi Floor. This data logger was recording up and down PAR, net and shf from the open space near the floor solar panels and net, RH and T and shf from under the trees.
2012-01-09	41907	CR1000	Installed		Installed in the Campbell Enclosure at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	41909	CR1000	Installed		Installed in the Campbell Enclosure at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	38970	CR3000	Installed		Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2013-01-06	12213	CR10X	Removed		Removed from the non-functional east sap flow station at Tonzi.
2013-10-18	31308	CR10X	Removed		The tram derailed at the far end of the track not stopping and reversing direction. Initially it reset okay moving to park, but it did not run on the hour. The data was corrupt, but I was able to upload programs and a new OS in the field. It still would not run. I brought it in for fixing.
2015-04-08	66250	CR1000	Installed		Installed with the Handar wind profile near the Floor tower.
2015-05-06	66249	CR1000	Installed	Data Logger IRT	Installed at Tonzi to the east just north of the road. This data logger is collecting data from the two IRT sensors
2015-12-23	66250	CR1000	Removed		Removed from the box for the wind profile near the Floor tower.
2016-07-07	19481	CR10X	Removed		Removed from the Floor soil temperature, SHF, RH&T and Pres. These sensors have been moved to the CR23x collecting soil moisture.
2016-10-13	48042	CR10X	Removed		Removed from the non-functioning sap flow station within the Tower cow fence
2016-10-13	47772	CR10X	Removed		Removed from the non-functioning sap flow station north of the road
2018-02-07	2113	CR6	Installed		Installed on Tonzi Tower for the Vaisala GMP CO2 profile.
2018-03-06	20138	CR10X	Removed		Removed from Tonzi tower's old CO2 profile system b/c the profile system was not working. It was replaced by sn 47253.
2018-03-06	47253	CR10X	Installed		Installed at Tonzi to try to fix the CR10x running the tower's old CO2 profile system. It replaced sn 20138.
2018-05-23	47253	CR10X	Removed		Removed from the Tonzi Tower with the old CO2 profile system. New Vaisala profile system is running
2019-01-13	20138	CR10X	Installed		Installed near the Floor solar panels to record temperatures from a concrete cal panel for the FLIR thermal camera.
2019-04-16	47772	CR10X	Removed		Removed with the wooden cal panel for the FLIR because cows chewed the TC wires and the new cal panel is better
2019-05-30	47772	CR10X	Installed		Installed near an oak tree about 25m north of the Floor solar panels to support two IRTs
2020-03-02	66249	CR1000	Maintenance	Data Logger IRT	I changed this data logger Pakbus id from 1 to 49 - the last two digits of its serial number.
2022-06-07	2143	CR23X	Removed	none	Disconnected and packed up on 05/26 but brought back to the lab today - no longer needed
2022-06-07	47772	CR10X	Removed		Disconnected and packed up on 05/26 but brought back to the lab today - no longer needed
2022-10-05	2301	CR23X	Removed	Data Logger Soil CO2	The soil co2 gradient system has not been in good condition for a long time. Finally getting around to removing the equipment from the field.
2022-11-03	2301	CR23X	Installed	none	Installed with the IRT sensor sn 7385 from the cal panel near the Floor solar panels for an IRT calibration for Robert's Oakley bike transect data this past summer
2022-11-17	2301	CR23X	Removed	none	Removed from Tonzi at the conclusion of the IRT calibration along with IRT sensor sn 7385
2023-06-16	4190	CR1000	Installed	none	Installed at the tower top as part of the Arduino RSB diffuse PAR prototype to compare with the BF5
2023-07-06	4190	CR1000	Removed		Removed from the Tower Top where it was part of the Arduino based RSB diffuse PAR prototype
2024-04-22	66249	CR1000	Removed	Data Logger IRT	Removed from the IRT tripod because cows had chewed the wires off.
2024-06-04	66249	CR1000	Installed	Data Logger IRT	Reinstalled at the little tree northeast of the Tower at Tonzi after having been removed to repair massive cable damage from cows
2024-10-29	13214	CR10X	Installed	Data Logger StemFlux East	Installed east of the Floor tower to measure tree trunk temperatures for Kuno's stem flux experiment
2024-10-29	3501	CR10X	Installed	Data Logger StemFlux West	Installed west of the Floor tower to measure tree trunk temperatures for Kuno's stem flux experiment
2024-10-29	19481	CR10X	Installed	Data Logger StemFlux North	Installed north of the Floor tower to measure tree trunk temperatures for Kuno's stem flux experiment
Forced Diffusion
2017-10-18	20160003	eosFD	Installed		Installed near the Tree 1 soil CO2 profile for three month experiment
2017-10-25	20160002	eosFD	Installed		Installed near the Open (East) soil CO2 profile for three month experiment
2017-12-14	20160002	eosFD	Removed		Removed from the Tonzi soil CO2 profile in the Open (East) location. This FD chamber has been reporting zero flux with nearly identical CO2 readings for both cells. The pump seems to be running though.
2018-01-15	20160003	eosFD	Removed		Removed from the soil co2 profile near Tree 1 for return to Eosense.
2019-11-19	FD20180068	eosFD	Installed	Forced Diffusion Tree 1	Installed under the tree at the Tonzi soil co2 profiles
2019-11-19	FD20180026	eosFD	Installed	Forced Diffusion Open	Installed in the open at the Tonzi soil co2 profiles
Gas Analyzer
2011-10-13	AKC-0479	LI-800	Removed		Removed from the CO2 profiles system because of strange values and would not calibrate.
2011-12-18	AKC-0479	LI-800	Removed		Removed from the co2 profile system on the Tonzi Tower because it reading was pegged at max (1000ppm). TC wires cut.
2013-05-08	AKC-0479	LI-800	Removed		This Li800 was removed from the CO2 profile system on the Tonzi Tower where is was often drifting out of range and railing.
2016-07-07	CGA-556	LI-820	Calibration		Last calibration was 2016-06-16 Cell T = 52.2, Pressure = 91.0 Zero Air offset = -2.0ppm Span CO2 405ppm offset = 5.0ppm Zero 0.9472 -> 0.9467 Span 0.8496 -> 0.8369
2017-11-29	75H-2182	LI-7500A	Removed		Removed from the Tonzi Tower for calibration. Replaced by sn 75H-2668
2018-02-20	75H-2182	LI-7500A	Calibration	Lab	Last calibration: 2017-08-16 AGC=87 SDM=0 DAC1=0 DAC2=0 Ambient P=101.1kPa, Tair=23.3C, Tdew=-.8C Zero Air at 250psi, LBL Air 408.97 at 1700 Tdewspan=16.00 CO2 zero 0.8832 -> .8844 Offset: 5.24ppm CO2 span 1.0123 -> 1.0215 Offset: -4.81ppm H2O zero 0.8436 -> .8446 Offset: 6.7ppm H2O span 1.0038 -> 1.0038 Offset: 0ppm Notes: I didn't do a new H2O span because the dewpoint measurement was hovering around 2C, when the dewpoint generator was set to 16.00C. There might be an issue with the dewpoint generator.
2017-11-29	75H-2180	LI-7500A	Removed		Removed from the Tonzi Floor for calibration. Replaced by sn 1594
2018-01-10	75H-2180	LI-7500A	Calibration	Lab	Last calibration: 2017-08-16 AGC=97.8 SDM=0 DAC1=0 DAC2=0 Ambient P=101.1kPa, Tair=17.4C, Tdew=10.6C Zero Air at 250psi, LBL Air 408.97 at 1700 Tdewspan=16.00 CO2 zero 0.9129 -> 0.9147 Offset: 7.92ppm CO2 span 1.0145 -> 1.0362 Offset: -10.74ppm H2O zero 0.8871 -> 0.8864 Offset: -4.2ppm H2O span 1.0164 -> 1.0168 Offset: -0.02ppm Notes:
2017-11-29	CGA-556	LI-820	Installed		Installed in the Tower CO2 profile system after lab cleaning and calibration
2017-12-14	CGA-556	LI-820	Removed		Removed from the Tower co2 profile for cleaning and calibration. The rest of the profile equipment was turned off
2018-02-21	CGA-556	LI-820	Installed		Installed in the old CO2 profile system on the Tower for comparison of the new GMP343 profile.
2018-05-23	CGA-556	LI-820	Removed		Removed from the Tonzi Tower with the old CO2 profile system. New Vaisala profile system is running
2023-09-19	0073	LI-7500A	Removed	Gas Analyzer CO2/H2O Floor	Removed from Tonzi-Floor for calibration. Replaced by sn 0041.
2023-10-05	0073	LI-7500A	Calibration	Lab	Last calibration: 2023-06-13 AGC=100.6 SDM= DAC1= DAC2= AIU sn AIU-1569, Presure A0=58.004, A1=15.479 Ambient P=100.39kPa, Tair=30.62C, Tdew=11.88C Zero Air at 725psi, AMP CA04119 524.77 at 800 Tdewspan=20.00 CO2 zero 0.9161 -> .9167 Offset: 2.66ppm CO2 span 1.0093 -> 1.0064 Offset: 2.19ppm H2O zero 0.8328 -> .8296 Offset: -17.9ppm H2O span 1.0281 -> 1.0109 Offset: .38ppm Notes: Vertical orientation. Slightly larger than usual H2O zero offset
2023-09-19	0041	LI-7500A	Installed	Gas Analyzer CO2/H2O Floor	Installed at Tonzi-Floor to replace sn 0073 for calibration.
2024-01-03	0041	LI-7500A	Calibration	Lab	Last calibration: 2023-09-18 AGC=100 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=22.7C, Tdew=7.3C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=20.0 CO2 zero 0.9965 -> 0.9963 Offset: -0.79ppm CO2 span 1.0192 -> 1.0217 Offset: -1.67ppm H2O zero 0.8236 -> 0.8245 Offset: 5.0ppm H2O span 1.0292 -> 1.0365 Offset: -0.16ppm Notes: H20 took a long time (40min) to stabilize - kept creeping up
2024-01-02	0041	LI-7500A	Removed	Gas Analyzer CO2/H2O Floor	Removed from Tonzi Floor for calibration. Replaced by sn 75H-2667.
2024-01-03	0041	LI-7500A	Calibration	Lab	Last calibration: 2023-09-18 AGC=100 SDM=0 DAC1=- DAC2=- AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.8kPa, Tair=22.7C, Tdew=7.3C Zero Air at 550psi, AMP CA04119 524.77 at 750 Tdewspan=20.0 CO2 zero 0.9965 -> 0.9963 Offset: -0.79ppm CO2 span 1.0192 -> 1.0217 Offset: -1.67ppm H2O zero 0.8236 -> 0.8245 Offset: 5.0ppm H2O span 1.0292 -> 1.0365 Offset: -0.16ppm Notes: H20 took a long time (40min) to stabilize - kept creeping up
2024-01-02	75H-2667	LI-7500A	Installed	Gas Analyzer CO2/H2O Floor	Installed at Tonzi Floor to replace sn 0041 for calibration.
2024-04-10	75H-2667	LI-7500A	Calibration	Lab	Last calibration: 2023-12-20 AGC=99.6 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.69kPa, Tair=24.8C, Tdew=11.0C Zero Air at 300psi, AMP CA04119 524.77 at 550 Tdewspan=20.00 CO2 zero 0.9413 -> .9409 Offset: -1.55ppm CO2 span 1.0207 -> 1.0213 Offset: -.35ppm H2O zero 0.8427 -> .8441 Offset: 8.5ppm H2O span 1.0363 -> 1.0404 Offset: -.09ppm Notes: Used 524.7 as the CO2 span point
2024-03-26	75H-2667	LI-7500A	Removed	Gas Analyzer CO2/H2O Floor	Removed from Tonzi Floor for calibration. Replaced by sn 75H-2176.
2024-04-10	75H-2667	LI-7500A	Calibration	Lab	Last calibration: 2023-12-20 AGC=99.6 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.69kPa, Tair=24.8C, Tdew=11.0C Zero Air at 300psi, AMP CA04119 524.77 at 550 Tdewspan=20.00 CO2 zero 0.9413 -> .9409 Offset: -1.55ppm CO2 span 1.0207 -> 1.0213 Offset: -.35ppm H2O zero 0.8427 -> .8441 Offset: 8.5ppm H2O span 1.0363 -> 1.0404 Offset: -.09ppm Notes: Used 524.7 as the CO2 span point
2024-03-26	75H-2176	LI-7500A	Installed	Gas Analyzer CO2/H2O Floor	Installed at Tonzi Floor to replace sn 75H-2667 for calibration.
2024-07-19	75H-2176	LI-7500A	Calibration	Lab	Last calibration: 2024-03-23 AGC=103 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.4kPa, Tair=21.2C, Tdew=16.5C Zero Air at 1700psi, AMP CA04119 524.77 at 350 Tdewspan=20.00 CO2 zero 0.8682 -> .8677 Offset: -2.2ppm CO2 span 1.0079 -> 1.0132 Offset: -3.94ppm H2O zero 0.8494 -> .8578 Offset: 52.3ppm H2O span 0.9236 -> .9377 Offset: -.34ppm Notes: First calibration after swapping internal chemicals on 2024-07-15. It has been running in the lab since the chemical swap. I used "524.75" as the CO2 span point in the 7550 software. I will test it again in a few days to make sure it's stable.
2024-06-19	75H-2176	LI-7500A	Removed	Gas Analyzer CO2/H2O Floor	Removed from Tonzi Floor for calibration. Replaced by sn 0041.
2024-07-19	75H-2176	LI-7500A	Calibration	Lab	Last calibration: 2024-03-23 AGC=103 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.4kPa, Tair=21.2C, Tdew=16.5C Zero Air at 1700psi, AMP CA04119 524.77 at 350 Tdewspan=20.00 CO2 zero 0.8682 -> .8677 Offset: -2.2ppm CO2 span 1.0079 -> 1.0132 Offset: -3.94ppm H2O zero 0.8494 -> .8578 Offset: 52.3ppm H2O span 0.9236 -> .9377 Offset: -.34ppm Notes: First calibration after swapping internal chemicals on 2024-07-15. It has been running in the lab since the chemical swap. I used "524.75" as the CO2 span point in the 7550 software. I will test it again in a few days to make sure it's stable.
2024-06-19	0041	LI-7500A	Installed	Gas Analyzer CO2/H2O Floor	Installed at Tonzi Floor to replace sn 75H-2176 for calibration.
2024-10-22	0041	LI-7500A	Calibration	Lab	Last calibration: 2024-06-17 AGC=98.9 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.7kPa, Tair=25.7C, Tdew=11.4C Zero Air at 1050psi, AMP FB04319 514.07 at 800 Tdewspan=20.00 CO2 zero 0.9958 -> .9960 Offset: .54ppm CO2 span 1.0176 -> 1.0142 Offset: 2.36ppm H2O zero 0.8238 -> .8244 Offset: 3.3ppm H2O span 1.0341 -> 1.031 Offset: .08ppm Notes:
2024-09-27	0041	LI-7500A	Removed	Gas Analyzer CO2/H2O Floor	Removed from Tonzi Floor for calibration. Replaced by sn 0065.
2024-10-22	0041	LI-7500A	Calibration	Lab	Last calibration: 2024-06-17 AGC=98.9 SDM= DAC1= DAC2= AIU sn AIU-1866, Presure A0=58.31, A1=15.48 Ambient P=100.7kPa, Tair=25.7C, Tdew=11.4C Zero Air at 1050psi, AMP FB04319 514.07 at 800 Tdewspan=20.00 CO2 zero 0.9958 -> .9960 Offset: .54ppm CO2 span 1.0176 -> 1.0142 Offset: 2.36ppm H2O zero 0.8238 -> .8244 Offset: 3.3ppm H2O span 1.0341 -> 1.031 Offset: .08ppm Notes:
2024-09-27	0065	LI-7500A	Installed	Gas Analyzer CO2/H2O Floor	Installed at Tonzi Floor to replace sn 0041 for calibration.
2024-10-10	TG1-0421	LI-7700	Installed	Gas Analyzer CH4 Tower	Installed on top of the Tower by adding a new mount using L-brackets and a rail fitting removing existing Allen screws and reusing the sockets for standard 1/4-20 bolts. Wash box and spiked hat also installed.
2024-10-10	TG1-0514	LI-7700	Installed	Gas Analyzer CH4 Floor	Installed on the Floor tower by adding a new mount using L-brackets and a rail fitting removing existing Allen screws and reusing the sockets for standard 1/4-20 bolts. No wash box, hat but no spikes.
Heat Flux Plate
2001-01-05	00068	HFP01SC	Installed	Heat Flux Plate D	Likely first installation date and location estimated from notes and data.
2001-01-05	000144	HFP01	Installed	Heat Flux Plate E	Likely first installation date and location estimated from notes and data.
2001-01-05	000140	HFP01	Installed	Heat Flux Plate C	Likely first installation date and location estimated from notes and data.
2001-01-05	000138	HFP01	Installed	Heat Flux Plate A	Likely first installation date and location estimated from notes and data.
2001-01-05	000139	HFP01	Installed	Heat Flux Plate B	Likely first installation date and location estimated from notes and data.
2011-11-16	000144	HFP01	Removed	Heat Flux Plate E	I removed this heat flux plate from the Tonzi understory location due to bad readings. I found that a gopher had cut the cable. In addition the the insulation on the cable was cracked and rotting.
2011-12-01	000144	HFP01	Installed	Heat Flux Plate E	Reinstalled in the field in its orginial location. The ground was dry and crumbly.
2012-01-09	2495	HFP01SC	Installed		Installed at -8cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	2500	HFP01SC	Installed		Installed at about 1m agl at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-09-05	000139	HFP01	Removed	Heat Flux Plate B	Removed from Tonzi Floor for repair and calibration. This sensor was about 3cm below the ground surface. The insulation of its cable was all cracked and rotting. This was SHF plate #2.
2012-11-07	000139	HFP01	Installed	Heat Flux Plate B	Installed after calibration by Sebastian in BC. The original calibration factor was found to be stable. It was placed just south of the stand holding the HMP45 near another SHF plate. Siyan wants to keep the new plate litter-free to compare to the older plate. Both plates are near the south edge of the canopy and should get nearly full sunlight except for the shadow from the tower.
2024-02-16	00068	HFP01SC	Maintenance	Heat Flux Plate D	I dug this plate up. It was at about -10cm with voids below the plate. I soldered on a new cable amd cut off the calibration cable because the insulation on both was completely rotten. I put it back at -2cm.
2024-03-07	000138	HFP01	Maintenance	Heat Flux Plate A	We dug this plate up to replace its cable that had all its insulation rotted off. The plate was 2-5cm below the surface – it was tilted and ground surface was not very flat. We put it back flat at 3cm and the new cable in conduit.
2024-03-07	00068	HFP01SC	Moved	Heat Flux Plate D	I moved this plate back down to -10cm where I found it before fixing its cable a couple weeks ago.
2024-04-22	000139	HFP01	Removed	Heat Flux Plate B	Removed from Tonzi floor met because a cow had chewed the wire and pulled the plate out of the ground.
2024-05-08	000139	HFP01	Installed	Heat Flux Plate B	Reinstalled at Tonzi Floor in flexible aluminum conduit. It might be at about -5cm - I was a little overwrought at the time.
2024-05-15	000141	HFP01	Maintenance	Heat Flux Plate F	Rewired to new junction box and updated data logger program.
Infrared Temperature
2010-12-09	1281	SI-121	Removed		Removed from Tonzi with the end of the surface temperature experiment.
2010-12-09	1282	SI-121	Removed		Removed from Tonzi with the end of the surface temperature experiment.
2012-01-09	NO1107535	OS136-1-MVC	Installed		Installed at SP3 southeast of the Tower. The sensor is pointing at the ground to the south at about a 45deg angle from vertical. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	NO1107536	OS136-1-MVC	Installed		Installed at SP2 near the Tower. The sensor is pointing at the ground to the south at about a 45deg angle from vertical. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2015-05-06	1965	SI-121	Installed	Infrared Temperature Tree Crown	Installed at Tonzi to the east just north of the road. This sensor is point down on top of a small tree.
2015-05-06	1964	SI-121	Installed	Infrared Temperature Grass A	Installed at Tonzi to the east just north of the road. This sensor is point down on a patch of ground cleared of grass.
2018-06-01	7385	SI-131	Installed		Installed near the Floor Tower on a CR10X to give temperatures of a black panel as a reference for the thermal camera.
2019-01-13	1624	SI-121	Installed	Infrared Temperature Ref Panel B	Installed on a post pointing to the northeast and slightly downward at the south facing concrete reference panel near the Floor solar panels. The panel also was five thermocouples embedded in it.
2019-04-16	7385	SI-131	Removed		Removed with the wooden cal panel for the FLIR because cows chewed the TC wires and the new cal panel is better
2019-05-30	TS01-001	TS01	Installed		Installed near the Floor solar panels looking at the grass to the north. Footprint of about 0.7m x 0.35m diameter
2019-05-30	7638	SI-131	Installed		Installed near an oak tree about 25m north of the Floor solar panels. Measuring trunk temperature from about 40cm distance.
2019-05-30	TS01-002	TS01	Installed		Installed near an oak tree about 25m north of the Floor solar panels. Measuring trunk temperature from about 110cm distance.
2019-05-30	7385	SI-131	Installed		Installed near the Floor solar panels looking at the grass to the north. Footprint of about 1.23m x 2.5m diameter
2019-11-19	TS01-001	TS01	Removed		Removed from near the Floor solar panels. This sensor was looking at the grass. Ana needed its narrow FOV for her emissivity testing in the lab.
2021-03-17	7385	SI-131	Removed	Infrared Temperature Grass B	A cow ate the wire from the sensor to the data logger box. Removed for repair in the lab.
2021-05-04	7385	SI-131	Installed	Infrared Temperature Grass B	Reinstalled after cows chewed the cable and the first attempt at a splice had a bad solder joint.
2021-06-02	7385	SI-131	Moved	Infrared Temperature Grass B	Moved from pointing at the cal panel to pointing at the grass. It was moved to the cal panel to replace the IRT there for cleaning. I realized later that the grass is probably more important than cal panel but there should be a mini inter-comparison now.
2021-06-24	1624	SI-121	Installed	Infrared Temperature Ref Panel B	Reinstalled after several tries where the wiring was confused. Originally removed because a wasp filled its port with mud and larva.
2022-06-07	7385	SI-131	Removed	Infrared Temperature Grass B	Disconnected and packed up on 05/26 but brought back to the lab today - no longer needed
2022-06-07	7638	SI-131	Removed		Disconnected and packed up on 05/26 but brought back to the lab today - no longer needed
2022-06-07	1624	SI-121	Removed	Infrared Temperature Ref Panel B	Disconnected and packed up on 05/26 but brought back to the lab today - no longer needed
2022-06-07	TS01-002	TS01	Removed		Disconnected and packed up on 05/26 but brought back to the lab today - no longer needed
2022-10-20	NO1107536	OS136-1-MVC	Removed	none	This sensor has not been sending good data from a while. Seems a woodpecker destroyed its window. Removed and brought in for disposal
2022-10-20	7385	SI-131	Installed	Infrared Temperature Ref Panel A	Install at the Tonzi cal panel for calibration. But I damaged the data logger so not collecting data until next time.
2022-11-17	7385	SI-131	Removed	Infrared Temperature Ref Panel A	Removed from Tonzi at the conclusion of the IRT calibration along with CR23X sn 2301
2024-04-10	1964	SI-121	Removed	Infrared Temperature Grass A	Removed from the IRT tripod at Tonzi where it was pointed at the ground. The cows ate its cable.
2024-04-22	1965	SI-121	Removed	Infrared Temperature Tree Crown	Removed from the IRT tripod because cows had chewed the wires off.
2024-06-04	1964	SI-121	Installed	Infrared Temperature Tree Crown	Reinstalled at the little tree northeast of the Tower at Tonzi after having been removed to repair massive cable damage from cows. This sensor is pointed at the tree crown.
2024-06-04	1965	SI-121	Installed	Infrared Temperature Grass A	Reinstalled at the little tree northeast of the Tower at Tonzi after having been removed to repair massive cable damage from cows. This sensor is pointed at the grass.
2024-10-29	7385	SI-131	Installed	Infrared Temperature StemFlux East	Installed east of the Floor tower to measure tree trunk temperatures for Kuno's stem flux experiment
2024-10-29	7638	SI-131	Installed	Infrared Temperature StemFlux West	Installed west of the Floor tower to measure tree trunk temperatures for Kuno's stem flux experiment
2024-10-29	1624	SI-121	Installed	Infrared Temperature StemFlux North	Installed north of the Floor tower to measure tree trunk temperatures for Kuno's stem flux experiment
Interface
2012-01-09	1327	CE4	Installed		Installed in the Campbell Enclosure at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	1328	CE4	Installed		Installed in the Campbell Enclosure at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	1329	CE4	Installed		Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2015-04-08	13053	NL115	Installed		Installed with the Handar wind profile near the Floor tower.
2015-12-23	13053	NL115	Removed		Removed from the box for the wind profile near the Floor tower.
LED sensor
2018-05-23	LED-05	LED-NDVI	Removed		Removed from the Tonzi Tower because it has not been working for a while and there are Decagon SRS sensors from NDVI and PRI
Moisture Point
2001-11-10	000000402165	PRB-K Type #8	Installed		Installed near the understory tower by Dennis and Liukang
2001-11-10	000000574B4B	PRB-K Type #8	Installed		Installed near the Floor solar panels by Dennis and Liukang
2001-11-10	000000402FF3	PRB-K Type #8	Installed		Installed near the water potential table and original sap flow measurements by Dennis and Liukang
2001-11-10	000000574632	PRB-K Type #8	Installed		Installed near the soil co2 measurements tower by Dennis and Liukang
2003-04-16	0000097A432E	PRB-K Type #8	Installed		Installed at Tonzi furthest from big tree by Liukang
2003-04-16	0000097A3C6E	PRB-K Type #8	Installed		Installed at Tonzi third closets to big tree by Liukang
2003-04-16	0000097A3B40	PRB-K Type #8	Installed		Installed at Tonzi second closest to big tree by Liukang
2003-04-16	0000097A4AAA	PRB-K Type #8	Installed		Installed at Tonzi closest to big tree by Liukang
2005-01-27	00000A6D882B	PRB-K Type #8	Installed		Installed at Tonzi by minirhizotron transect west of soil CO2 profiles
2005-01-27	00000A3D04E8	PRB-K Type #8	Installed		Installed at Tonzi by minirhizotron transect west of soil CO2 profiles
2005-01-27	00000A6D72F5	PRB-K Type #8	Installed		Installed at Tonzi by minirhizotron transect west of soil CO2 profiles
2015-04-08	000007931AFE	PRB-K Type #8	Removed		Removed from a location near the main tower ground sensors due to a broken pin (2nd from bottom). Replaced by sn 00000128B8072
2015-04-08	00000128B8072	PRB-K Type #8	Installed		Installed in a location near the main tower ground sensors to replace sn 000007931AFE that has a broken pin.
2016-11-17	00000128B8072	PRB-K Type #8	Removed		Removed from Tonzi near the main tower. This probe has two broken pins.
2016-11-17	00000FEDDAA1	PRB-K Type #8	Installed		Installed at Tonzi near the main tower to replace sn 00000128B8072 that has two broken pins
2017-12-14	000000574632	PRB-K Type #8	Removed		Removed from the location inside the soil co2 profile fence. This probe has been giving bad readings for a while and its lowest pin is broken off.
2019-12-03	000000574B4B	PRB-K Type #8	Removed		Removed from Tonzi near the Floor solar panels. This probe has three broken pins and has not been measured in a long time but this was the first time the soil was wet enough to remove it by hand.
2021-02-10	000000402FF3	PRB-K Type #8	Removed	Soil Moisture Probe F -0.50m	Removed from Tonzi floor due to fixed readings for a long while. This sensor was out of the ground at the edge of the trees near the path to the tower. It was buried vertically with the top of the sensor 31cm below the surface - the time were 44-50cm below the surface.
2024-01-02	00000A3D04E8	PRB-K Type #8	Removed	none	This probes has been broken for a long time - more than a year. Removed. It has a broken pin and the shaft is cracked.
Multiplexer
2010-02-10	14049	AM416	Removed		This mux was removed from Tonzi. It was used for sap flow just west of the floor tower. CR10X sn 38347 was removed with it.
2010-06-24	14049	AM416	Installed		This multiplexor was installed with two soil heat flux plates in the floor radiation system. The HMP45C lines were moved from the CR10X to the multiplexor to make room for the multiplexor.
2011-02-03	14049	AM416	Removed		Removed with other equipment from near the Floor site at Tonzi. Used in recording supplimental PAR, net, shf and RH and T.
2012-01-09	10208	AM16/32B	Installed		Installed in the Campbell Enclosure at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	10195	AM16/32B	Installed		Installed in the Campbell Enclosure at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	10194	AM16/32B	Installed		Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-09-06	1237	AM16/32A	Removed		Removed with all the above ground components of the C1 sap flow station. This sap flow station has not been working for a while and there are no plans to continue sap flow measurements in the future.
2013-05-30	1164	AM16/32A	Removed		Removed from the East sap flow station. This station had not been running for a long time. The data logger had been removed previously. The box, solar panel and above ground cables were removed also.
2016-10-13	1429	AM16/32A	Removed		Removed from the non-functioning sap flow station within the Tower cow fence
2016-10-13	1430	AM16/32A	Removed		Removed from the non-functioning sap flow station within the Tower cow fence
2016-10-13	1236	AM16/32A	Removed		Removed from the non-functioning sap flow station north of the road
2023-10-04	1237	AM16/32A	Removed	Multiplexer Tower	Removed from the Tower top due to spikes on multiple channels. Replaced by sn 31675
2023-10-04	31675	AM16/32B	Installed	Multiplexer Tower	Installed on the Tower top to replace sn 1237 which was removed due to spikes on multiple channels.
Narrow Band
2017-09-07	943203017	SRS-Nr NDVI	Installed		Installed on the post holding the floor met data logger box. This sensor is point to the north and about 30 degrees up to see just the trees and not the grass.
2020-10-22	943203017	SRS-Nr NDVI	Removed		Removed from the Tonzi floor met because it was no longer being used - tree NDVI pointing to the sky doesn't work
Net Radiometer
2001-05-20	990351	NR-LITE	Installed		Installed on the Tower top with the initial set up of the site
2002-02-08	990350	NR-LITE	Installed	Gas Analyzer CO2/H2O	Installed inside the orange fence on the floor met CR10x data logger.
2010-03-16	990350	NR-LITE	Installed		Installed at the request of Hideki under the oak canopy near the radiation tram at Tonzi.
2010-03-16	041556	NR-LITE	Installed	none	Installed at the request of Hideki in an unshaded opening near the east end of the radiation tram.
2011-02-03	990350	NR-LITE	Removed		Removed from under the trees near the floor tower.
2012-01-09	1514	NR01	Installed		Installed at -8cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
PAR Sensor
2001-05-07	LQ1570	Line Quantum	Moved	none	Moved from Vaira to Tonzi
2001-05-20	990021	PAR-LITE	Installed		Installed on the Tower top as a calibration sensor
2001-05-20	990019	PAR-LITE	Installed		Installed on the Tower Top in the incoming PAR position.
2001-05-20	990017	PAR-LITE	Installed		Installed on the Tower top in the reflected PAR location with the initial set up of the site
2001-09-07	Q29881	LI-190SA	Installed	PAR Sensor Incoming	Installed on the Tower top in the incoming position
2001-09-07	Q29892	LI-190SA	Installed		Installed on the Tower top in the outgoing position
2004-04-30	010159	PAR-LITE	Installed	PAR Sensor Incoming Cal	Installed on the radiation boom in the incoming position for inter-comparison with the existing Licor Quantum sensor.
2004-04-30	030382	PAR-LITE	Installed	PAR Sensor Reflected Cal	Installed on the radiation boom for comparison with existing Licor Quantum sensor
2007-01-19	Q29892	LI-190SA	Removed		Removed from Tonzi Tower top.
2007-01-19	Q29881	LI-190SA	Removed	PAR Sensor Incoming	Removed from Tonzi Tower top.
2010-03-16	010161	PAR-LITE	Installed		Installed at the request of Hideki in an unshaded opening near the east end of the radiation tram at Tonzi. This sensor is pointing upward collecting incoming PAR.
2010-03-16	010163	PAR-LITE	Installed		Installed at the request of Hideki in an unshaded opening near the east end of the radiation tram. This sensor is pointed downward collecting reflected PAR.
2011-02-03	010161	PAR-LITE	Removed		Removed from the open space near the floor solar panels.
2011-02-03	010163	PAR-LITE	Removed		Removed from the open space near the floor solar panels.
2016-07-07	LQ1570	Line Quantum	Removed		Discovered buried in grass and soil near the other floor sensors after years of being missing. Brought in to be cleaned up and tested.
2020-04-18	110340	PQS 1	Installed	PAR Sensor Under-A	The PAR sensor was installed at Tonzi on the z-cam 1 post to measure below canopy PAR. It is connected the the fmet CR23x
2021-01-21	990031	PAR-LITE	Installed	none	Installed as part of the inter-comparison kit to test PAR, AirT and RH on the top of the Tower.
2021-02-10	990031	PAR-LITE	Removed	PAR Sensor Incoming Cal	Removed from Tonzi Tower after three weeks of inter comparison with the AMP standard
2021-04-01	010164	PAR-LITE	Location	PAR Sensor Incoming	Location for sensors currently at Tonzi
2021-04-01	030382	PAR-LITE	Location	PAR Sensor Reflected	Location for sensors currently at Tonzi
2021-08-11	110340	PQS 1	Removed	PAR Sensor Under-A	Removed from Tonzi near z-cam 2 because the data seems not so useful.
2021-10-06	010164	PAR-LITE	Removed	PAR Sensor Incoming	Removed from Tonzi-Tower due to bad readings from a broken wire. Replaced by sn 110340.
2021-10-06	110340	PQS 1	Installed	PAR Sensor Incoming	Installed at Tonzi to replace sn 010164 due to bad readings from a broken wire.
2022-10-20	030382	PAR-LITE	Removed	PAR Sensor Reflected	Removed from Tonzi due to random spikiness. Replaced by sn 990025.
2022-10-20	990025	PAR-LITE	Installed	PAR Sensor Reflected	Installed at Tonzi to replace sn 030382 that has been spiky.
2023-06-16	010164	PAR-LITE	Installed	none	Installed at the tower top as part of the Arduino RSB diffuse PAR prototype to compare with the BF5
2023-07-06	010164	PAR-LITE	Removed		Removed from the Tower Top where it was part of the Arduino based RSB diffuse PAR prototype
Precipitation
2012-01-09	48102-611	TE525	Installed		Installed on the ground at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	48132-611	TE525	Installed		Installed on the ground at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	48130-611	TE525	Installed		Installed on the ground at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2018-10-17	24872-999	TR-525I-R1	Calibration		Got 88 of 100 tips - adjusted screws 2.5 turns CW
2018-10-17	48130-611	TE525	Calibration		Got 88 of 100 tips - adjusted screws 2.5 turns CW
2018-10-17	48132-611	TE525	Calibration		Got 134 of 100 tips - adjusted screws 4 turns CCW
2019-10-24	24872-999	TR-525I-R1	Calibration		I connected the bucket to a CR23x dripping 475ml of water through the bucket which should result in 100tips. I got 100 tips.
2019-10-24	48130-611	TE525	Calibration		I connected the bucket to a CR23x dripping 475ml of water through the bucket which should result in 100tips. I got 104 tips. I did not adjust it.
2019-11-07	48132-611	TE525	Calibration		Plug tipping bucket into the calibration CR23x and dripped 475ml of water through the bucket which should result in 100tips. Got 103 tips and did not adjust the bucket.
2019-11-07	48102-611	TE525	Calibration		Plug tipping bucket into the calibration CR23x and dripped 475ml of water through the bucket which should result in 100tips. Got 103 tips and did not adjust the bucket.
2020-12-18	48130-611	TE525	Removed	none	Removed from OSU SP1 for experiments in the lab. The cable was disconnected inside the tipping bucket and left in place in the field.
2021-10-06	48132-611	TE525	Calibration	none	Tested with our new method using the peristaltic pump and 237ml of water which should result in 50 tips. 1/2 turn of the screws (CW+, CCW-) should adjust the number of tips by 2-3% (1-1.5 tips). Got 52 tips – I turned the screws one turn CCW.
2021-10-06	48102-611	TE525	Calibration	none	Tested with our new method using the peristaltic pump and 237ml of water which should result in 50 tips. 1/2 turn of the screws (CW+, CCW-) should adjust the number of tips by 2-3% (1-1.5 tips). Got 50 tips – No adjustment
2021-10-06	24872-999	TR-525I-R1	Calibration	none	Tested with our new method using the peristaltic pump and 237ml of water which should result in 50 tips. 1/2 turn of the screws (CW+, CCW-) should adjust the number of tips by 2-3% (1-1.5 tips). Got 54 tips – I turned the screws two turns CCW
Radio
2012-01-09	35754	RF401	Installed		Installed in the Campbell Enclosure at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	35787	RF401	Installed		Installed in the Campbell Enclosure at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	35785	RF401	Installed		Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	1131631861	Raven XT	Installed		Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2017-03-02	21520	RF400	Removed		Removed from the soil co2 box. The radio link stopped working in the field and I plan to use the old MD9 to replace it anyway.
2017-03-02	21519	RF400	Removed		Removed from the Tower computer box. The radio link stopped working in the field and I plan to use the old MD9 to replace it anyway.
2018-12-19	35754	RF401	Removed		Removed from the OSU SP3 system to test out data collection by LattePanda in the lab.
2018-12-19	35785	RF401	Removed		Removed from the OSU SP1 system to test out data collection by LattePanda in the lab.
2019-03-11	34362	RF401	Installed		Installed in the Tower computer box to connect the computer to the remote data loggers.
2019-03-11	35754	RF401	Installed		Installed in the OSU SP3 box to connect to the Tower computer.
2019-04-16	35785	RF401	Installed		Install in the OSU SP1 box near the soil co2 system to connect the CR3000 to the Tower computer. Using Pakbus mode at 38400
2020-03-02	32468	RF401	Installed	Radio IRT	Installed on the CR1000 for the small tree IRT system.
2022-02-09	5A0331744701B101	LX40-NA-WIFI	Installed	Radio Cell Modem	Add to the Tower top data logger box to provide remote connection.
2024-04-22	32468	RF401	Removed	Radio IRT	Removed from the IRT tripod because cows had chewed the wires off.
2024-06-04	32468	RF401	Installed	Radio IRT	Reinstalled at the little tree northeast of the Tower at Tonzi after having been removed to repair massive cable damage from cows
RH & Temp
2003-01-21	U3030032	HMP45AC	Removed	none	Removed from Tonzi. Replaced by sn W0510026
2003-01-21	W0510026	HMP45AC	Installed	none	Installed at Tonzi to replace sn U3030032 for calibration.
2010-03-16	W0510026	HMP45AC	Installed		Installed with radiation sensors for Hideki near the tram and floor eddy tower. This sensor is under the oak tree canopy.
2011-02-03	W0510026	HMP45AC	Removed		Removed from under the trees near the floor tower.
2016-11-02	L2310711	HMP60	Installed		Installed on the top of the Tonzi Tower to compare with the existing HMP45 there.
2017-08-25	L2310711	HMP60	Removed		Removed from Tonzi and brought back to the lab. It was installed for a comparison with an HMP45. The sensor is ready to use.
2018-01-15	L2310711	HMP60	Installed		Insalled by a box just below the 3rd lowest location of the tower co2 profile. This sensor will be used to give real time air temperature to the GMP343s.
2024-02-27	E5736	HygroVUE10	Installed	RH & Temp	Installed in the Floor RH/T location. Will cross compare with existing HMP45 before removing the old sensor.
2024-03-26	W0510026	HMP45AC	Removed	RH & Temp Floor	Removed for Tonzi Floor met due to age and poor RH data. Replaced by new Hygrovue a few weeks ago.
Soil Moisture Probe
2001-01-05	31/016	ML2x	Installed		Installed at Tonzi at -25cm under the trees.
2001-01-05	31/085	ML2x	Installed		Installed at the Tonzi Tower at -20cm in the open.
2001-01-05	31/033	ML2x	Installed		Installed near the Tonzi Tower at the surface.
2001-01-05	31/092	ML2x	Installed		Installed near the Tonzi Tower at -20cm in the open.
2001-01-05	31/100	ML2x	Installed		Installed near the Tonzi Tower at -20cm under the trees.
2001-03-01	54/009	ML2x	Installed		Installed near the Tonzi Tower at -50am.
2001-03-01	54/004	ML2x	Installed		Installed near the Tonzi Tower at -50cm
2012-01-09	5TM-1342	STD-5TM	Installed		Installed at -2cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1286	STD-5TM	Installed		Installed at -5cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1315	STD-5TM	Installed		Installed at -10cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1388	STD-5TM	Installed		Installed at -20cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1297	STD-5TM	Installed		Installed at -45cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1395	STD-5TM	Installed		Installed at -30cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1296	STD-5TM	Installed		Installed at -65cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1306	STD-5TM	Installed		Installed at -2cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1285	STD-5TM	Installed		Installed at -5cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1282	STD-5TM	Installed		Installed at -10cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1396	STD-5TM	Installed		Installed at -20cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1407	STD-5TM	Installed		Installed at -30cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1308	STD-5TM	Installed		Installed at -50cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TM-1405	STD-5TM	Installed		Installed at -70cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TE-1278	STD-5TE	Installed		Installed at -2cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TE-1287	STD-5TE	Installed		Installed at -10cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TE-1281	STD-5TE	Installed		Installed at -5cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TE-1393	STD-5TE	Installed		Installed at -20cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TE-1275	STD-5TE	Installed		Installed at -40cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TE-1274	STD-5TE	Installed		Installed at -60cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	5TE-1400	STD-5TE	Installed		Installed at -80cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2021-03-17	139/052	ML2x	Installed	Soil Moisture Probe F -0.50m	Installed in the same location and depth as the one the died and was previously removed. This probe is buried vertically with its times at 44-50cm. It is at the drip line of the tree to the SE of the data logger box.
2022-06-07	2676	SoilVUE10	Installed	Soil Moisture Probe H Profile	I installed this probe in the open to the south of the Floor met boxes towards the Tower along the existing power conduit. I cut a hole in the conduit and ran the cable back to the Floor CR23x. This is SoilVue B in the data.
2022-06-07	2674	SoilVUE10	Installed	Soil Moisture Probe I Profile	I installed this probe to the west of the Floor met boxes near the existing Moisture Point probe and soil matrix sensor under the trees. This is SoilVue A in the data.
2022-06-07	2688	SoilVUE10	Installed	Soil Moisture Probe J Profile	Installed near the OSU-SP1 soil sensors. This is SoilVue C in the data.
2024-05-08	31/100	ML2x	Removed	Soil Moisture Probe B -0.20m Tree	Removed from Tonzi because I cut its cable while digging a hole to reinstall a SHF plate. I'm sure this was #2 on the data logger ant the smap entry says tree, but this was about 3m south of the box in a mostly open area. Tines were vertical 16-22cm deep.
2024-05-22	31/100	ML2x	Installed	Soil Moisture Probe B -0.20m Tree	Reinstalled in the original location after being repaired in the lab for cow chew
Soil Water Potential
2012-01-09	15843	SX229	Installed		Installed at -10cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15942	SX229	Installed		Installed at -65cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15824	SX229	Installed		Installed at -5cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15825	SX229	Installed		Installed at -30cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15833	SX229	Installed		Installed at -20cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15839	SX229	Installed		Installed at -45cm at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15856	SX229	Installed		Installed at -50cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15840	SX229	Installed		Installed at -30cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15822	SX229	Installed		Installed at -10cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15846	SX229	Installed		Installed at -5cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15818	SX229	Installed		Installed at -20cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15836	SX229	Installed		Installed at -70cm at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15764	SX229	Installed		Installed at -80cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15730	SX229	Installed		Installed at -40cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15852	SX229	Installed		Installed at -5cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15802	SX229	Installed		Installed at -10cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15729	SX229	Installed		Installed at -20cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	15731	SX229	Installed		Installed at -60cm at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2022-04-27	G20007112	TEROS21	Installed	Water Potential A	Installed near the drip line of the trees near the Tower Moisture Point probe
2022-04-27	G20010035	TEROS21	Installed	Soil Water Potential B	Installed near the base of a tree near the Tower Moisture Point Probe
2022-06-07	G20007096	TEROS21	Installed	Soil Water Potential C	Installed near the OSU-SP1 soil sensors at -10cm, vertical orientation
2024-05-08	G20007096	TEROS21	Removed	Soil Water Potential C	Removed from the OSU SP1 system at Tonzi for testing. It wasn't giving data. Cows might have damaged its cable.
2024-05-15	G20007096	TEROS21	Installed	Soil Water Potential C	Reinstalled in close to the original location at about -10cm after repairing the cow chewed cable in the lab
Solar Controller
2016-03-08	0135002X	PS-30M	Moved		I moved this charge controller from the Tram solar system to the main Tower power system. The existing charge controller at the tower sn 02431248 stopped reading the battery voltage.
2017-09-28	SCC-001	C60	Removed		Removed from the Tonzi Tower solar system. The system was upgraded with a new MPPT charge controller.
2017-09-28	0135002X	PS-30M	Removed		Removed from the Tonzi Tower solar system were it was serving as a Low Voltage Disconnect. The system was upgraded with a new MPPT charge controller.
2017-09-28	KB04594	MNKID-B	Installed		Installed on the Tonzi Tower to upgrade the solar system. The solar system is now three parallel strings of four panels in series approximately 12A at 80VDC. The battery bank was rewired to be a 24V system.
2018-04-25	186580399	PS-30M	Location		This charge controller is running the soil CO2 solar system. The system is 24V. It has been here for at least the last 10 years.
2018-05-11	3317052234210	CMTD-As4s0	Installed	none	Installed at the Road Well to power Global Water sensor.
2020-07-07	0127000A	PS-30M	Removed	none	Removed from the Floor solar system. I needed a 30A model for the tower going to Steve and Sabina. Since updating this system 24V the amp load has decreased below 15A. Replaced by sn 12501584.
2020-07-07	186580399	PS-30M	Removed		Removed from the Soil CO2 box under the tree. This is an old 1st generation model. I put in a newer 15A 2nd model sn 12501588 since the power requirements here are small.
2020-07-07	12501584	PS-15M	Installed	none	Installed at Tonzi to replace sn 0127000A for use elsewhere. Since updating the solar power to 24V the 30A model is not required.
2020-07-07	12501588	PS-15M	Installed	none	Installed in the Soil CO2 box under the tree at Tonzi. I swapped out an old 1st gen 30A model sn 186580399.
2023-03-01	12501588	PS-15M	Removed	Solar Controller Soil CO2	This solar controller has not been showing solar amps and doesn't seem to charge batteries. I brought it in for testing
2023-03-01	21501223	SS-6L-12V	Installed	Solar Controller Soil CO2	Installed at the soil CO2 battery bank to replace sn 12501588 that doesn't seem to be charging batteries.
Solar Panel
2010-08-19	04592G0181	KC40	Removed	none	Removed from the Tram charging station so that two 20W panels could be use for a 24V system.
2012-01-09	T21009229B43638	SX350J	Installed		Installed at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	T21009229B43579	SX350J	Installed		Installed at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-01-09	T21009229B37030	SX350J	Installed		Installed at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ.
2012-02-09	020854E-6-03-02-06905	SP75	Removed	Solar Panel Floor G	Removed from the Floor solar system. This panel has not been connected to the system since at least August 2008
2012-02-09	020854E-6-03-02-06862	SP75	Removed	Solar Panel Floor H	Removed from the Floor solar system. This panel has not been connected to the system since at least August 2008
2022-02-09	T21009229B43579	SX350J	Removed		Removed from OSU SP2 with the dying battery. Replaced with a power line from the Tower battery bank.
Water Level
2018-02-07	1260403156	CTD-10	Installed		Installed in the well near the Floor tower. The sensor is 11.1m below the top of the white pipe. It is connected to the CR200.
2018-03-27	57278	WL16U	Removed	Water Level Floor	Removed from the Floor Well. The cable insulation is rotting and needs to be replaced. Replaced by the new METER water level sensor a couple of weeks ago.
2018-05-11	57278	WL16U	Installed	Water Level Road	Installed at the Road Well to measure water level at 5min intervals storing 30min averages
2021-04-18	1260403156	CTD-10	Removed	Water Level Floor	I found it's cable chewed. I cut of the chewed part and reattached but still no data. Power and data lines seems continuous. Maybe chewing shorted out something.
2021-05-04	1260403156	CTD-10	Installed	Water Level Floor	Reinstalled after cows chewed the extension cable and Joe couldn't figure out the wiring.
Weather Station
2019-07-02	A000251	Mark I	Installed		Installed at the top of the tower east of the southeast corner. Should be remounted on the radiation boom.
2021-08-11	A000251	Mark I	Removed	Weather Station	Removed from the Tower top due to not sending data and one of the incoming sensors was removed by woodpeckers.

Export to BADM