Equipment and Calibration
View History
Equipment Entry
|
Documents
PackingSlip: ps_Dynamax_20120313.pdfHistory
| Rec No. | Date | Loc From | Title | Loc To | Notes |
|---|---|---|---|---|---|
| 5179 | 2021-03-11 | Lab none | Installed | Hill Slough Anemometer | Installed at Hill Slough with site setup. |
| 5173 | 2021-03-10 | Lab none | Adjusted | Lab none | Changed baud rate from 19,200 to the max 57,600. |
| 4100 | 2019-09-04 | Bouldin Alfalfa-ReleaseEx Anemometer Reflected | Removed | Lab none | Removed from Bouldin Alfalfa with the end of the CH4 release experiment. This unit was in the lowest inverted position on the secondary tower. |
| 4088 | 2019-08-16 | Lab none | Installed | Bouldin Alfalfa-ReleaseEx Anemometer Reflected | Installed for CH4 release experiment. This unit was mounted in an inverted position to measure wind at near max canopy height. |
| 3876 | 2019-02-06 | Loaned | Returned | Lab none | Returned by Tibisay Perez who used it at Whendee Silver's compost pile experiment in Marin |
| 3476 | 2018-06-04 | Lab none | Loaned | Loaned | Loaned to Tibisay Perez in Whendee Silver's lab for use at their Marin compost site while one of their sonics is repaired - one month maybe. |
| 3108 | 2017-10-04 | East End-Temp3 Anemometer | Removed | Lab none | Removed with the decommissioning of Temporary Tower #3 - Boardwalk site. |
| 2881 | 2017-06-23 | Lab none | Installed | East End-Temp3 Anemometer | Installed at the East End Temporary Tower #3 Boardwalk location with the initial setup of the site. |
| 2601 | 2017-01-27 | Lab none | Upgrade | Lab none | Upgraded firmware to correct for W bug.
Old SN: Y120907 New SN: X120907 Upgrade file: Y074417-Y124215-m.gcu Old firmware: 2329-114 New firmware: 2329-116-01 All Checksum fields report PASS. Log file: WMUpgradeLog_Y120907_170127_135608.txt Config file below. If there are two entries in a field, the first entry is the old setting and the second entry is the new setting. ------- THE FOLLOWING FIELDS HAVE CHANGED Output rate : P1 1 Hz Output rate : P8 20 Hz THE NEW CONFIGURATION IN FULL ==== DETAILS OF DETECTED ANEMOMETER ======================= Serial Number : X120907 ---- SW VERSION ------------------------------------------- Anemometer Firmware Version: 2329-116 ---- HW DETAILS OF ANEMOMETER------------------------------ Detected Anemometer Class : WindMaster 20Mhz Number of AXIS on this unit : 3 DAC resolution of attached unit : 14 Number of DAC channels : 4 Maximum sampling rate : (8) P8 20 Hz ---- USER CONFIGURATION OF ANEMOMETER---------------------- Baud Rate : 19200 Output Message Format : M1 UV(W) Output Message Velocity Units : m/s Output Message Terminator : Retries : ON Instantaneous Sampling : OFF Factory Calibration : ON Physical Communications : Auto Resolution settings : High resolution Alignment settings : North to spar Averaging settings : Averaging inactive Output rate : P1 1 Hz Output rate : P8 20 Hz Polar angle minimum magnitude: 0.050 m/s Power-On Message : Display Power On Message ASCII Format : Comma Separated (CSV) SOS and Sonic Temperature display : SOS Analogue output mode : -5V to 5V Unit Identifier : 'Q' Output Channel 1 : U output (full range = 30m/s) Output Channel 2 : V output (full range = 30m/s) Output Channel 3 : W output (full range = 5m/s) Output Channel 4 : Speed of Sound |
| 2580 | 2017-01-17 | West Pond Anemometer | Removed | Lab none | Removed from West Pond and returned to lab for firmware upgrade. It was replaced by sn 120908. |
| 583 | 2012-05-02 | Lab none | Installed | West Pond Anemometer | Installed on folding boom at the top of the tower. |