Equipment and Calibration
Equipment history at Tonzi| ALL | | Anemometer || Barometer || Battery Bank || Camera || CO2 Probe || Data Logger || Forced Diffusion || Gas Analyzer || Heat Flux Plate || Infrared Temperature || Interface || LED sensor || Moisture Point || Multiplexer || Narrow Band || Net Radiometer || PAR Sensor || Precipitation || Radio || RH & Temp || Soil Moisture Probe || Soil Water Potential || Solar Controller || Solar Panel || Water Level || Weather Station |
SELECT a.recno, a.eh_date, a.eh_loc1, a.eh_loc2, IF(a.eh_loc2=:loc, a.eh_locref2, a.eh_locref1) AS ref, a.eh_locref2, a.eh_title, a.eh_notes, a.eh_id, b.serialno, b.equip, b.modelno FROM equiphist a INNER JOIN equiplist b ON a.eh_id=b.recno WHERE (a.eh_loc1=:loc1 OR a.eh_loc2=:loc2) AND b.equip=:eq ORDER BY b.serialno, a.eh_date
| Date | Serial No. | Model | Action | Ref | Notes |
|---|---|---|---|---|---|
| Multiplexer | |||||
| 2012-01-09 | 10194 | AM16/32B | Installed | Installed in the Campbell Enclosure at SP1 inside the soil co2 fence. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. | |
| 2012-01-09 | 10195 | AM16/32B | Installed | Installed in the Campbell Enclosure at SP2 near the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. | |
| 2012-01-09 | 10208 | AM16/32B | Installed | Installed in the Campbell Enclosure at SP3 southeast of the Tower. This is the initial setup of the site by Richard Cuenca and Yutaka Hagimoto of Oregon State Univ. | |
| 2013-05-30 | 1164 | AM16/32A | Removed | Removed from the East sap flow station. This station had not been running for a long time. The data logger had been removed previously. The box, solar panel and above ground cables were removed also. | |
| 2016-10-13 | 1236 | AM16/32A | Removed | Removed from the non-functioning sap flow station north of the road | |
| 2012-09-06 | 1237 | AM16/32A | Removed | Removed with all the above ground components of the C1 sap flow station. This sap flow station has not been working for a while and there are no plans to continue sap flow measurements in the future. | |
| 2023-10-04 | 1237 | AM16/32A | Removed | Multiplexer Tower | Removed from the Tower top due to spikes on multiple channels. Replaced by sn 31675 |
| 2010-02-10 | 14049 | AM416 | Removed | This mux was removed from Tonzi. It was used for sap flow just west of the floor tower. CR10X sn 38347 was removed with it. | |
| 2010-06-24 | 14049 | AM416 | Installed | This multiplexor was installed with two soil heat flux plates in the floor radiation system. The HMP45C lines were moved from the CR10X to the multiplexor to make room for the multiplexor. | |
| 2011-02-03 | 14049 | AM416 | Removed | Removed with other equipment from near the Floor site at Tonzi. Used in recording supplimental PAR, net, shf and RH and T. | |
| 2016-10-13 | 1429 | AM16/32A | Removed | Removed from the non-functioning sap flow station within the Tower cow fence | |
| 2016-10-13 | 1430 | AM16/32A | Removed | Removed from the non-functioning sap flow station within the Tower cow fence | |
| 2023-10-04 | 31675 | AM16/32B | Installed | Multiplexer Tower | Installed on the Tower top to replace sn 1237 which was removed due to spikes on multiple channels. |